The shear stress-strain diagram for an alloy is shown in the figure below (Figure 1). Take ✓ = 0.3. Figure 7 (ksi) K 0.004 Ty=50 y (rad) < 1 of 2 > Part A If a bolt having a diameter of 0.27 in. is made of this material and used in the lap joint, determine the modulus of elasticity E. (Figure 2) Express your answer to three significant figures and include appropriate units. E 3.25x10 ksi Submit Previous Answers ✓ Correct Part B Determine the force P required to cause the material to yield. Express your answer to three significant figures and include appropriate units. P= 5.73 μÃ 5 Submit Previou Answers Request Answer X Incorrect Enter your Provide Feedback ksi ? Wrong

The shear stress-strain diagram for an alloy is shown in the figure below (Figure 1). Take ✓ = 0.3. Figure 7 (ksi) K 0.004 Ty=50 y (rad) < 1 of 2 > Part A If a bolt having a diameter of 0.27 in. is made of this material and used in the lap joint, determine the modulus of elasticity E. (Figure 2) Express your answer to three significant figures and include appropriate units. E 3.25x10 ksi Submit Previous Answers ✓ Correct Part B Determine the force P required to cause the material to yield. Express your answer to three significant figures and include appropriate units. P= 5.73 μÃ 5 Submit Previou Answers Request Answer X Incorrect Enter your Provide Feedback ksi ? Wrong

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I Review Part A The two bars shown in the figure below (Figure 1) are made of a material that has the stress-strain diagram shown. (Figure 2) If the cross-sectional area of bar AB is 2.4 in? and BC is 5.0 in?, determine the largest force P that can be supported before any member fractures. Assume that buckling does not occur. Express your answer to three significant figures and include appropriate units. HA P = Value Units Submit Request Answer Figure 1 of 2 Provide Feedback Next > 4 ft 3 ft P Pearson
Q-2 A portion of the stress–strain curve for a stainless steel alloy is shown in Figure Q-2. A 550 mm long bar is loaded in tension until it elongates 4.4 mm, and then the load is removed. (a) Determine the permanent set in the bar. (b) Determine the length of the unloaded bar. (c) If the bar is reloaded, determine the proportional limit. [Use the figure to make necessary drawings/markings to show your solution strategy!
What is the tensile strength of the bar if the yield stress is equal to 275MPa?
Please help with this question in detail. I need every single step of the process. Thanks!
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.86 in.² and bar (2) has a cross-sectional area of 0.47 in.2. After load P is applied, the strain in bar (1) is found to be 780 μe. Assume L₁-52 in., L₂=74 in., a=20 in., b=25 in., and c-33 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. Answers: (a) σ1 (b) VD=i (c) P = i L eTextbook and Media Save for Later (1) B L2 b (2) ksi, 0₂ = in. kips. i D P ksi. Attempts: 0 of 5 used Submit Answer
A 1 in x2 in ductile cast iron bar should operate for 9 years at 650 ° C. What is the maximum load that can be applied? (See Figure)
A column made from cast iron has a cross section of A = 8272mm². On the column, a load of F = 667.4kN is acting. The compression strength of the material is σ = 355 N mm². Calculate the acting compressive stress for this case: (±0.5) N mm² What is the safety factor against fracture, if an actual compressive N stress of 198.08. is acting: mm² (±0.1)
Consider the truss shown in (Figure 1). Each member has a cross-sectional area of 8.0(10³) mm² and is made of A- 36 steel. Take P = 150 kN. Figure P 4 m A -3 m B 1 of 1 Part A Determine the total strain energy stored in the truss. Express your answer to three significant figures and include the appropriate units. U₂ = Submit μA Value Provide Feedback Request Answer Units ?
100 mm must elongate only 5 mm when a tensle load of 100,000 N is applied. Under these A cylindrical specimen of a brass alloy having a circumstances what must be the radius of the specimen? Consider this brass alloy to have the stress-strain behavior shown in Figure below. Tensile strengh 450 MPa (65,000 p A00 10 pu 300 200- 30 Yield strength 250 MPa (36,000 psi 2아 100 1아 100 0.005 0.20 0.30 0.40
3. Two brass rods (one square, one circular) are extruded; initial and final dimensions are provided below. Which part is expected to have the greater tensile strength? Which part is expected to have the greater ductility? Part Initial Dimensions Final Dimensions Cylindrical D=2.5 in D = 2.35 in. Square 4 × 4 in. 3.9 × 3.9 in.