can you please find out the solution for this? 1. The bar is made out of steel and is loaded as shown in figure Fig. – 1. Determine the designstress if the bar has the cross section shown in figure Fig. – 2.0.50 (m)20 (KN]20 (kN]ICFigure - 1Figure - 22. A steel square wire is (2 x 2 mm), and 2 [m] long. A force of 18[N] is applied to it and it stretches0.3 [mm]. Assume the material is elastic. Determine the stress in the wire O and the strain inthe wire E.

Answered: Image /qna-images/answer/2888d3dc-391b-4454-9484-fdb8a239e9a5.jpg

1. The bar is made out of steel and is loaded as shown in figure Fig. - 1. Determine the design stress if the bar has the cross section shown in figure Fig. - 2. 0.50 (m] 20 (KN) 20 (kN) A Figure - 1 Figure - 2 2. A steel square wire is (2 x 2 mm), and 2 [m] long. A force of 18[N] is applied to it and it stretches 0.3 (mm). Assume the material is elastic. Determine the stress in the wire O and the strain in the wire E. .

1. The bar is made out of steel and is loaded as shown in figure Fig. - 1. Determine the design stress if the bar has the cross section shown in figure Fig. - 2. 0.50 (m] 20 (KN) 20 (kN) A Figure - 1 Figure - 2 2. A steel square wire is (2 x 2 mm), and 2 [m] long. A force of 18[N] is applied to it and it stretches 0.3 (mm). Assume the material is elastic. Determine the stress in the wire O and the strain in the wire E. .

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Which process will be done after hardening process? Why?
3. Explain the whole process of steel making from raw materials till steel beams (steps and the processes). Additionally, explain continuous casting in detail.
What is sand casting? Explain the steps in sand casting process with neat diagram and indicate all the parts of it.
Draw the cooling curve for steam cooling from 115C to -5 Label each phase (solid, liquid, gas), and each phase change (ie: vaporization, condensation, melt, freeze, sublimation, deposition, etc) on your graph. Reminder: Temperature is on your Y-axis and heat is on your X-axis.
What manufacturing processes would you use to make this? Make sure to focus onusing appropriate terminology and include the terms: blanking, punching, flange-rolling, & stamping to describe the process steps for how this stainless-steel colanderwas produced
i need the answer quickly
What is pressure die casting? Explain the six major steps in pressure die casting process with neat diagram and indicate all the parts of it.
MENG364 MANUFACTURING TECHNOLOGY
The first photo was the screenshot of my question here in Bartleby. But in other site (chegg), I saw the same problem but the answers are different. On another site also, the answers are the same as of chegg—however, "member AB" was stated, and not BA. I am hoping for clarification on what process to use, and why. Thank you
A hydraulic press for compacting powdered PRACTICE samples has a large cylinder which is 10.0 cm in diameter, and a small cylinder with a diameter of 2.0 cm (Fig. 9). The piston of the small cylinder is attached to the midpoint of a lever that is hinged at point C as shown in the figure. The sample, which is placed on the large cylinder, has an area of 4.0 cm?. What is the pressure on the sample if 350 N is applied at the end of the lever? (Giancoli, 2014) F2 350 N Sample- F Hydraulic. fluid 10.0 cm Small cylinder -2.0 cm
where are the steps for the solution?????