A steel column is a cylinder 6.8 m long and 0.35 m in diameter. What is the change in length of the column when it experiences a tensile stress resulting from the application of a 3600 N force? The elastic modulus for steel is 20 × 1010 Nm2/kg2. ΔL = m

A steel column is a cylinder 6.8 m long and 0.35 m in diameter. What is the change in length of the column when it experiences a tensile stress resulting from the application of a 3600 N force? The elastic modulus for steel is 20 × 1010 Nm2/kg2. ΔL = m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A member is formed by connecting two aluminium bars as shown below. calculate the magnitude force P that will cause the total length of the member to increase 0.5 mm. the values of elastic modulus for aluminium is 69 GPa. Ø6 Ø15 25 cm_ 250mm P.
Determine the instantaneous stress and elongation of a 30 mm diameter bar if a mass of 60 kg falls through a height of 60 mm on to a collar which is rigidly attached to the bottom end of the bar as shown in Figure Q2. The bar is 1.2 m long and is suspended vertically. The Modulus of elasticity, E, for the material of bar is 210 GPa. Take g = 10 m/s2.
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.24 mm the values of elastic modulus for steel is 221 MPa. Take H1 = 4 cm, H2 is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. = 9 cm, top bar (R) IP Solution: R cm x RCm Steel bar i) Magnitude Force, P = H1 cm ii) Stress-induced in the top bar = Q cm x Q cm Steel bar H2 cm iii) Stress-induced in the bottom bar =
The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross- sectional area of the wire is 1.75 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. D 90 cm 90 cm B 180 cm Ale 120 cm
The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange 8 to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1). A (1) 120 in. B 30 kips 30 kips 144 in. C
Q1: 30-mm-diameter steel bar is to be used as a torsion spring. If the torsional stress in the bar is not to exceed 110 MPa when one end is twisted through an angle of 30°, what must be the length of the bar in m? modulus of rigidity=80 GPa . (close to two decimal)
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2 Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1). The axial displacement of the free end is..... mm
Two round solid bars of different materials are connected in series against rigid supports as shown in Figure 4. Determine the stress in each bar and the support reactions if temperature is increased by 18° C. Bar A da, EA, A Bar B dв, Ев, ав LA LB Figure 4 Use the following information. Bar, B: Length, LB Diameter, dB Poisson's Ratio Young's Modulus EB = 210 kN/mm2 Coefficient of expansion aB = 12.4x106 °C- Bar, A: Length, LA Diameter, dA = 25mm =D40 mm = 10 mm 30 mm S. = 0.28 =D0.32 = 70 kN/mm² Coefficient of expansion aa = 16.5x10-6 °C-I Poisson's Ratio %3D Young's Modulus EA
L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is subjected to loads of PR = 112 kN and Pe = 18 kN. Segments AB and BC have elastic moduli of E, = 206 GPa and E = 73 GPa. The rod has circular cross-sections, and the dimensions of the rod are given above. Find the overall change in length of the rod under this load. Assume: • The collar at B is rigid • Stress concentration effects may be neglected 2014 Michael Swanbom
A solid bar of length L = 4 m and diameter 200 mm is heated from 20 to 320 degrees celsius and restrained between two solid immovable walls. Young's modulus of the material is 90 GPa and the coefficient of thermal expansion is 22 x 10-6/°C. →Calculate the thermal strain, e, in micro-strain correct to two decimal places. micro-strain. Calculate the thermal stress, o, in megapascals (MPa) correct to two decimal places. E: σ: MPa. Hence calculate the force exerted by the bar in meganewtons (MN) correct to two decimal places: F MN. L