A rectangular titanium plate has the following dimensions. a = 20 mm, b = 15 mm, and c=5 mm. Uniformly distributed tensile forces of 7.50 kN act in the z direction. Determine the strains in the x, y, and z directions. Let E = 120 GPa, and v = 0.35.

A rectangular titanium plate has the following dimensions. a = 20 mm, b = 15 mm, and c=5 mm. Uniformly distributed tensile forces of 7.50 kN act in the z direction. Determine the strains in the x, y, and z directions. Let E = 120 GPa, and v = 0.35.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.26P: - 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v...

See similar textbooks

Related questions

Q: The state of plane strain on an element has components of Ez = 500 (10-6), y = 300(10-6), and…

Q: Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and…

A: Given that, Esteel=20×1010PaEbrass=10×1010Pa

Q: The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made from…

Q: Consider a linear rectangular thin sheet of metal, subjected to uniform uniaxial tensile stress of…

A: A linear rectangular thin sheet of metal, subjected to a uniform uniaxial tensile stress of 100 MPa…

Q: (a) the strains in these directions, (b) the changes in dimensions, (c) the volumetric strain and…

Q: teel plate (E = 31000 ksi, G= 12000 ksi, alpha (a) = 6 * 10 ^ -6 1/F ) with dimensions a = 20 in and…

A: GivenE=31000ksiG=12000ksiα=6×10-6 /Foa=20inb=13int=7.5inσ=-50ksi∆T=100Fo

Q: Compound axial member ABC has a uniform diameter of d = 1.45 in. Segment (1) is an aluminum [E₁ =…

Q: A solid steel rod is connected to an arm loaded by to forces, F-1 kN and F₂ -1.2 KN. A three-element…

A: Given Data: F1=1 kNF2=1.2 kNεa=60 μεεb=135 μεεc=264 μεθ1=0oθ2=60oθ3=120o To Find: The linear strain…

Q: A thin metal alloy plate is loaded by biaxial stress (2 directions) given by 8000 psi in the x…

Q: is shown below, 400 300 200 100 Stress (MPa)

A: 1.Modulus of elasticity can be obtained by taking the slope of stress-strain curve in elstic…

Q: E120 = +625 Eo = +950 Ez40 = +300

A: For solution refer below images.

Q: For the state of a plane strain with Ex, Ey and yxy components: (a) construct Mohr's circle and (b)…

A: εx = 250 × 10-6εy =310 x 10-6Yxy = -100 × 10-6

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

Question

A rectangular titanium plate has the following
dimensions. a = 20 mm, b = 15 mm, and c=5 mm. Uniformly distributed tensile forces of 7.50 kN act in the z direction. Determine the strains in the x, y, and z directions. Let E = 120 GPa, and v = 0.35.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

2) Find the strains in the 1-2 coordinate system (local axes) in a unidirectional boron/epoxy lamina with 50% fiber volume fraction, if the stresses in the 1-2 coordinate system applied to are ơ1 = 6 MPa, ơ2 =2 MPa, and T12 = -4 MPa. Use the properties of the given unidirectional lamina in the book and assume plane stress conditions for the lamina.
Figure Q2 (b) shows a strain rosette that is attached on the surface of a production equipment.The strain readings are εa = -200(10-6), εb = -65(10-6) and εc = 130(10-6).i) Determine the in-plane principal strains and sketch the strain element.ii) Determine the maximum in-plane shear strain and sketch the strain element.iii) What is the angle of orientation (with respect to x-axis) that leads to εx’ = 0?
A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rod (2) is 1020 μin./in. Assume initial rod lengths of L1 = 148 in. and L2 = 78 in. Determine(a) the normal strain in rods (1).(b) the normal strain in rods (1) if there is a 0.043 in. gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied.(c) the normal strain in rods (1) if there is a 0.043 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied.
Please help me answer this thank you
The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6. (a) Use the strain transformation equations to determine the equivalent strain components on an element oriented at an angle of 0 = 30° counterclockwise from the original position. (b) Sketch the deformed element due to these strains within the x-y plane.
A thin plate is subjected to a biaxial stress field of  x= 1 Gpa and  y= 0.5 Gpa. Calculate the strains in the xy directions if the plate is made of (a) steel, (b) a 0° unidirectional boron-epoxy composite. For the boron-epoxy composite use the following properties: Young’s Modulus at 0°=207 Gpa, modulus at 90° = 19 Gpa,  12=0.21, G12= 6.4 Gpa. Assume for steel a young’s modulus = 207 GPa
My answer is displayed and incorrect. Please give answer in ksi.
4. A rigid steel bar is supported by three circular rods as shown in Figure below. There is no strain in the rods before the load P is applied. After load P is applied, in rod (2) is 1,090 µ. Assume initial rod lengths of L1 = 3400mm. and L2 = 1800mm. Assuming the system is symmetrical, determine: a. The normal strain in rods (1). b. The normal strain in rods (1) if there is a 2mm gap in the connections between normal strain the rigid bar and rods (1) at joints A and C before the load is applied. c. The normal strain in rods (1) if there is a 2mm gap in the connection between the rigid bar and rod (2) at joint B before the load is applied. (1) (1) (2) L Rigid har O O
4 of 4 (b) The 45° strain rosette is mounted on a steel shaft. The following readings are obtained from each gauge are shown in Figure Q2(b). i. ii. Ea = 800 x 106, & = 520 x 106 and & = -450 x 10-6 , Find the strains values in the x-y directions and draw the strain element diagram of that direction. Find the principal strain values and draw the strain element diagram of that direction. iii. Find the maximum shear strain value and draw the strain element diagram of that direction. iv. If the properties of the structure have E = 208 GPa and v = 0.28, find the magnitude of the principal stresses. b 45° 45° Figure Q2(b)[ [8 marks]
Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and 2 cm in diameter. The combination is subjected to a tensile force of 5000 N. Find the strain in each rod. Young's Modulus of Steel use 20×10¹⁰ Pa, of brass use 10×10¹⁰ Pa. Find the elongation of each rod.
The rigid beam is supported by a pin at A and wires BD and CE. Figure 3 m 2m 1 of 1 4 m ▾ Part A If the load P on the beam causes the end C to be displaced 8 mm downward, determine the normal strain developed in wire CE. (Figure 1) ECE = Submit ▾ Part B EBD = Submit V—| ΑΣΦ Determine the normal strain developed in wire BD. Provide Feedback Request Answer ΑΣΦ vec Request Answer vec SO ? ? mm/mm mm/mm Next >
Compound axial member ABC has a uniform diameter of d=1.45 in. Segment (1) is an aluminum [E1=10,000 ksi] alloy rod with a length of L1=88 in. Segment (2) is a copper [E2=17,000 ksi] alloy rod with a length of L2=128 in. When axial force P is applied, a strain gage attached to copper segment (2) measures a normal strain of ε2=2200 μin./in. in the longitudinal direction. What is the total elongation of member ABC? answer is in inches