The strain in the a direction at point A on the A-36 structural-steel beam is measured and found to be 210(106). The modulus of elastisity and shear modulus for A-36 steel are 29(10) ksi and 11(10) ksi respectively. (Eigute.1) Figure 1 of 1 TOI Part B Determine the shear strain Yey at point A Express your answer using three significant figures. ΗΨΗ ΑΣΦ | 11 vec 3 A Yay 29.12-10 4 Submit Previous Answers Request Answer X Incorrect; Try Again SPAC

Q: Find the value of a. TO a. Vs +3

A:

Q: A tank (contains a fluid of density=1318.4 kg/m3) stands on a frictionless cart (The cart is fixed)…

A:

Q: X 300 mm D 800 mm B

A:

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: If Ma- 68.5 kN-m and Mc- 56.0 kN-m, use the graphical method to construct the bending -moment…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: X 300 mm D 800 mm B

A: For constant angular velocity, angular acceleration is zero,

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: (Determine the (f_x ) when force 80 N and angle 30° on the axis (X .A 69N .B 69.28lb .C 69.28N .D…

A:

Q: Describe the Parallel-Axis Theorem for an Area?

A:

Q: Move the forces in the shape to point a

A:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A: According to the question data MA=200lb.inclockwise   and the figure  We need to find Force F to…

Q: slove f

A:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: handle should be identified as a point of interest. Determine the Degree of freedom.

A:

Q: A hollow tube with thickness t = 1/4 in. is applied with a tensile load of 33 kips. Compute its…

A: Given data,  Tensile load P= 33kips = 33000 lbs  t= 1/4 in  Tensile stress S= 12 ksi = 12000 lb/in²…

Q: Solve erf only

A: Given:To Find: the value of x.Note: In the above equation,

Q: Please now solve 3

A: this question is based on the concept of material science.

Q: G₁ Go CODOVODS G₂ G₁ G

A:

Q: 4. What is the cost of 23' of cable if 34' costs $76.00? (round to nearest dollar)

A: Given-            Cost of 34ft cable=$76 To be determine-             Cost of 23ft cable