Determine the vertical component of the pin reaction at C.

Q: Find the external reactions of the Fixed Support at A.

A:

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at B and…

A: Consider the free body diagram as shown below.

Q: 10 m 0.5 kN downward 0.5 kN upward 5 kN-m C

A: Option b is correct.

Q: Let the normal force at the smooth peg B be NB, and the reactions at A be Ax and Ay, respectively.…

A: Consider the free body diagram of the system as shown below.

Q: Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by…

A: Introduction We will calculate the reaction force at A and B that is created by belts B and D in…

Q: How about this part :"Determine the x and y components of reaction the pin C exerts on member EDC…

A: F1 = 8 KN

Q: An 18-ft simply supported beam AB is subjected to a distributed load that varies liniarly from 300…

A: Since there are no horizontal forces acting, we consider only vertical reactions at A and B. The…

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is…

A: There will be two reactions at thrust bearing and tension in the cable. Since Force F acts in single…

Q: The uniform 15-m pole has a mass of 150 kg and is supported by its smooth ends against the vertical…

A: Given:m=150 KgL=15 m

Q: loh: proced ● Determine reactions at A and C A 2 m MB 1m -C Rc

A:

Q: 6) Find the horizontal and vertical components of the reactions at points A and D. 2m D -1.5 m B 1.5…

A: Given

Q: The compound beam is supported by a rocker at B and is fixed to the wall at A. Part A: If it is…

A: Given data as per the question Forces applied =500 lb and 200 lb Moment about point B =4000 lb.ft…

Q: Determine the magnitude of the vertical reaction force at D. Assume a = 4.9 ft, b = 9.8 ft, c = 19.6…

A:

Q: Determine internal reaction at the point located between A and C, 0.7 m to the right of A. Disregard…

A:

Q: Determine the magnitude of the reaction at support A, in lb. If: P = 342 lb, h = 19 in., A = 22 in.…

A:

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 195 lb, is…

A: Draw a diagram for the problem. Here, O is the origin, θ is the inclination of the force F with the…

Q: 2) Determine the reactions at A and D. (D is fixed to the soil) (take note of the sign) F1 F2 H. F3…

A: Given: F2(KN)=20 F1(KN)=5 F3(KN)=10 L1(m)=4 H(m)=-5

Q: Determine the reaction at C

A: Given data: M=5 kN.m Need to determine the reaction force at C.

Q: Determine the reaction at A on the beam. Let wo = 97 kN/m, L= 3 m.

A:

Q: 3. Draw a FBD. Determine the components of reaction at the fixed support A. Neglect the thickness of…

A:

Q: Determine the magnitude of the roller reaction at E. 400 kN

A: Given data To determine the reaction at the roller support.

Q: Determine the components of the support reactions at the fixed support A on the cantilevered beam. 6…

A: Draw the free-body diagram of the given beam.

Q: Question 1 Neglecting the weights of the bar and the pulley and assuming the weight of the ball B to…

A:

Q: Determine the reactions at supports A and B. A 500 lb/ft -6 ft 6 ft- 700 lb/ft -8 ft- 9 ft 6 ft

A: To find reactions at A and B

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.