Quiz 1/ For the circular cantilever rod of a diameter (10 cm) shown in figure 1. Knowing that the rod is subjected to a static force (F= 6 kN) and to static torque (T₁= 290π N. m) and (T2= 100π N. m) . Compute the factors of safety using both Tresca and von Mises failure theories, if the rod is made from steels a yield =320 Mpa. F T T-

Quiz 1/ For the circular cantilever rod of a diameter (10 cm) shown in figure 1. Knowing that the rod is subjected to a static force (F= 6 kN) and to static torque (T₁= 290π N. m) and (T2= 100π N. m) . Compute the factors of safety using both Tresca and von Mises failure theories, if the rod is made from steels a yield =320 Mpa. F T T-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
DOUBLE CHECK YOUR ANSWER AND SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer
Pravinbhai
please help solve and explain and include FBD please
What is the design stress in psi of an ASTM A313, gage number 8 spring wire. The type of application requires a factor of 0.34 for the type of service. Round your answer to 4 significant figures.
Answer is closer to 32 kN/m, but how does it get there?
Determine the factor of safety for infinite life fatigue (N > 1 million cycles) for a steel machine part experiencing max = 115 MPa, 0min = -45 MPa, Tmax = 40 MPa, and Tmin=-35 MPa. The material ultimate tensile strength is Sut = 435 MPa and the endurance limit strength has been determined as S₂ = 135 MPa. Report your answer with 2 decimal places.
Q2. Determine the safety factors for the bracket rod shown in Figure 2 based on both the distortion-energy theory and the maximum shear theory and compare them. Given: The material is 2024-T4 aluminum with a yield strength of 47 000 psi. The rod length /= 6 in. and arm a = 8 in. The rod outside diameter od 1.5 in., id = 1 in, h=2 in., t=0.5 in., Load F= 1000 lb. Assumptions: The load is static and the assembly is at room temperature. Consider shear due to transverse loading as well as other stresses. (Note: solve in SI units) wall tube Figure 2 arm
Given: A part is made of ductile material and subjected to principal stresses o1, 02, 03. It is statically loaded. Find: Determine the factor of safety for the part. Use the following parameters in your analysis: ơ1 40 kpsi, Sut = 90 kpsi, Suc = 20 kpsi, 02 = 5 kpsi, oz = -10 kpsi, Sy = %3D = –130 kpsi
A bracket shown in Fig.(2) is fastened to the wall by four bolts equispaced on a (10 cm) diameter bolt circle. The bracket is subjected to a fluctuating force (0-50 N) . Find the forces acting on each bolt and then choose a suitable bolt size and a preload that will give minimum safety factor (1.5) for any mode of failure.
please help
Please answer all 3 parts of the wuestion