Please complete parts 1-3. GIVEN:Hydraulic actuator clevis pin connection as shown below in the conceptual engineering sketch. Theactuator will deliver 50,000 lbf to the given clip assembly.GoodeDIA.#FJPART CA-口PAT B-B+PART AHINT: SUGGESTION MAKEPIN FROM STAINLESSSTEEL ANDFROM CARBON STEELCLIPSFIND:1. Calculate the bearing stresses on all the respective surfaces (i.e., mechanical components) that makeup the clip assembly (i.e., parts A, B, and C). Size the respective part dimensions to ensure adequatedesign margin (F.S.).2. Calculate the pin shear stress and size the pin dimensions (i.e., diameter of part C) to ensure adequateF.S. Only provide your final set of calculations3. Calculate the maximum bending and shear stresses in the support-beam clip (Part A) for your partdimensions. Only provide your final set of calculations.

Answered: Image /qna-images/answer/ac862260-79d3-47be-ba64-d581a18dc8fb.jpg

Answered: GIVEN: Hydraulic actuator clevis pin…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need clear ans and solve very very fast in 20 min and thank you | DYBALA? i need clear ans and solve very very fast in 20 min and thank you | DYBALA ?*! pressurized vessel (closed ends) with 500 bar, its dimensions are L = 1m, d = 25 Cm, D = 32 Cm, oy = 600 MPa. Find maximum values for Oh, o, and as then find safety factor. light shocks find its
10. A simply supported shaft between bearings camies a steady load of 10 kN at the centre. The length of shaft between bearings is 450 mm. Neglecting the effect of stress concentration, find the minimum diameter of shaft. Given that Endurance limit = 600 MPa; surface finish factor = 0.87; size factor = 0.85; and factor of safety = 1.6. [Ans. 35 mm]
inch with equations. Write a notes on heat balance sheet, draw that on the energy flow and enhance your answers 02/An indicator diagram taken from a single cylinder four stroke, compression ignition engine has a lt. th of 100 mm and an area of 2045 mm². The indicator pointer deflects a distance of 10 evlinder. If the bore and stroke of the enai a pressure increment o Late the mes er are both Pressure and the indicated 100 mm and the engine speed is 900 rev/... power. If the mechanical efficiency is 0.75, what is the brake power developed. Draw the indicator diagram. Q3/A diesel engine develops 5kW. Its indicated thermal efficiency is 0.3 and mechanical efficiency 0.75. Estimate the fuel consumption of engine in (a) Kg/hr (b) liters/hr (c) indicated specific consumption and (d) brake specific fuel consumption. Take heat value of fuel 42000 kJ/Kg and density of fuel 0.87 Kg/liter. Quiz (a) A diesel engine has brake thermal efficiency of 28 percentage. If the calorific value of fuel is…
Please provide Handwritten answer. show all tge steps and FBD. thank you:)
Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the value of acceleration due to gravity g to be 9.81 m/s², the value of y for carbon steel to be 76.5 × 103 N-m-3, and the value of Eto be 207 × 10⁹ N/m². NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the critical speed of a half-size model of the original shaft? The critical speed of a half-size model of the original shaft is rad/s.
Don't do copy paste from other platforms.
Please help. Written on paper not typed on computer or keyboard please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
can I got please the answer of these please
Describe the failure of a hollow torque tube. Calculate the forces creating the failure
part 4 please
Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
3) A double screw (Acme thread angle o = 14.5) mechanism is designed to lift a load of 18,000 lb in such a way that screw is loaded in tension. Use of Safe Factor of safety of 3.2. Select a suitable screw from data table provided in class notes for tensile load and shear load. Limiting tensile and shear stresses are 10,000 psi and 5,500 psi, respectively. Required thickness of Yoke which functions as a nut. It is desired to raise the hatch a total of 30.0 inches in 15 seconds. Use coefficient of friction f= 0.15. List necessary assumptions. Sketch and Label a schematic diagram. Determine a. Nominal major diameter of screw (D) b. Threads per Inch of selected thread (n) c. Thickness of Yoke (h) d. Lead angle (2) e. Torque required to raise the load (Tup) f. Torque required to lower the load (Tdown) g. Efficiency of the screw h. RPM required to operate each screw i. Compute the Total Power required to operate the mechanism.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS