3. From problem 2 HW2. Determine the safety factor if the pipe is made from cast iron (BRITTLE). Include a sketch of the failure envelope (σ - σ2 plane) to justify your answer. Use modified Mohr failure criteria. The cast iron properties are: ultimate strength in tension of 170 MPa, ultimate strength in compression of 650 MPa, modulus of elasticity of 70 GPa.

3. From problem 2 HW2. Determine the safety factor if the pipe is made from cast iron (BRITTLE). Include a sketch of the failure envelope (σ - σ2 plane) to justify your answer. Use modified Mohr failure criteria. The cast iron properties are: ultimate strength in tension of 170 MPa, ultimate strength in compression of 650 MPa, modulus of elasticity of 70 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Similar questions

Pravinbhai
A steam boiler, 1.2 meter in diameter, generates steam at a gauge pressure of 0.7 N/mm2. Assuming the efficiency of the riveted joints as 75%, find the thickness of the shell. Given that ultimate tensile stress = 385 MPa and factor of safety = 5
Pls help ASAP
Please answer all 3 parts of the wuestion
What is the design stress in psi of an ASTM A313, gage number 8 spring wire. The type of application requires a factor of 0.34 for the type of service. Round your answer to 4 significant figures.
I need to find the forces in each tube but I keep getting stuck. I have been getting really long equations to do algibra onwhich I suspect might be where the error was comming from. The values I have tried are F2 = -0.97786, and -4.889 kips
Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel to be 200 GPa: • Determine the slenderness ratio.
1.3-2 A load of P = 3.0 kips is applied to the connection. The failure stress of the pin material is 25 ksi. Design the diameter of the pin to the nearest 1/16-inch assuming a factor of safety of 2.
The fluctuating stresses listed in the table are found at a critical location of a component made of steel with Se = 40 ksi, Sy = 80 ksi, Sut = 110 ksi and f= 0.87. These stresses are applied on the part within 10 s. What is the accumulative damage of this part? What is the life of the part in hours if this stress pattern continues to repeat for the remained of the part's life? Use Goodman criterion and Miner's rule in your solution. Loading order |Omin o max |Number of cycles -20 30 -10 50 1 3. -30 30 1
8 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
Quick.
Assuming a welded rail line, 1km long, that is unconstrained except at the ends. The rail has a cross sectional profile as given. If the rail was installed at a temperature of 20°C, at what temperature would the rail buckle? How much pre-stress would need to be applied to the rail in order to prevent buckling up to a maximum operating temperature of 40°C? Rail profile 46E1 Equivalent profile name SBBI Section weight kg/m 46.17 Rail height mm (H) 145.00 X Y Y Head width mm (C) 65.00 A H Web thickness mm (A) 14.00 Foot width mm (P) 125.00 Moment of inertia, Ixx cm* 1641.10 Moment of inertia, lyy cm* 298.20