Show all the steps.Only Handwritten Buckling Factor of SafetyUsing a factor of safety with respect to buckling of 1.75,determine the largest load P the column can support.W12 x 87A-36 steel12 ASpeed00:28 / 08:53infoCC Part AIn the given problem, if the column is pinned-pinned, what would be the new critical load value?○ 922 kip○ 527 kip○ 475.2 kip○ 1900.8 kipSubmitRequest Answer

Per=(pi)2EI/(KL)2I= 384in^4KL=KxL=1x12x12= 144 in Per= (pi)^2 (29000)(384) / (144)^2Pallow= Per…

Answered: Buckling Factor of Safety Using a…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.7P

See similar textbooks

Similar questions

A fixed-pinned column is a W310 × 21 steel shape and is designed to carry an axial load of 125 kN. Determine the maximum permissible height L of the column if a factor of safety n = 2.5 is required with respect to the buckling of the column. Use E = 205 GPa and assume that the proportional limit is 340 MPa. The column may buckle about either axis of the cross section.
A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
Determine the allowable axial load Pallowfor a steel pipe column with pinned ends having an outside diameter of 220 mm and wall thickness of 12 mm for each oft he fol lowing lengths: L =2.5 m, 5 m, 75 m, and 10 m. (Assume E = 200 GPa and y = 250 MPa.)
A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The column has a length L = 4 m and is designed to support an axial load of 45 kN. Find the minimum required thickness of the section if the factor of safety n = 2.5 with respect to buckling. Assume that the modulus of elasticity is 72 GPa and the proportional limit is 480 MPa.
Please show the work in Handwritten format only
A long, slender structural aluminum [E = 69 GPa] flanged shape is used as al = 9.2-m-long column. The column is supported in the x direction at base A and pinned at ends A and C against translation in the y and z directions. Lateral support is provided to the column so that deflection in the x-z plane is restrained at mid-height B; however, the column is free to deflect in the x-y plane at B. Assume that b; = 102 mm, d = 122 mm, t; = 8 mm, and tw = 6 mm. Determine the maximum compressive load P the column can support if a factor of safety of 2.9 is required. In your analysis, consider the possibility that buckling could occur about either the strong axis (i.e., the z axis) or the weak axis (i.e., the y axis) of the aluminum column. P bf C L d Lateral B bracing L
Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy= 200 MPa. The pin joints are constructed with sufficient size and fit to provide good resistance to out-of-plane bending. Determine the factor of safety for out-of-plane buckling. 800 mm where F=1250 N B 400 mm F The factor of safety for out-of-plane buckling is
Be clear and box your answer please
Can someone slove the fx and fy equations in the below questions solution in steps to how we got f1 and f2 values. Thanks.
Select the lightest WT4 shape to be used as a 20 ft long tension member to resist the of dead load, D=40 k, live load, L=60 k, snow load, PS=25 k, and earthquake, E=110 k. The connection is two lines of bolts through the flange with three 3/4-in ∅ bolts in each line spaced at 3 in on center. Use A992 Grade 50 steel. Neglect block shear.
5. This bar is made of AISI 1006 cold-drawn steel (Sy = 280 MPa) and is loaded by the forces F = 0.45 kN, P = 6.0 kN, and T = 30 N-m. Determine the maximum length L of the bar that can be used without exceeding a static factor of safety of 2 for the entire bar (Based on the maximum shear stress theory). You need to find the most critical position. 100 mm 15-mm D.
Select the lightest W shape that will act as a column of 7 m long with both end hinged and support an axial load of12KN with the safety factor of 2.2, assume the proportional limit for steel is 200 Mpa and E=208 Gpa

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS