6.11 Determine and locate the resultant of the three forces acting on the ladder as shown in Figure 6.19. 735 N -1.5 m وس 1735 835 A 150 1502 100+735 = 835 √√8352 +150 150 N 100 N1 1 m 1 m- 4 m =848N.

Q: b) Write the Advantages of Stress, Strain diagram in your own words

A:

Q: 10 Fig. (6) 8 MPa

A: Given Dataσx=8MPaθ=24°

Q: In your summer internship, you are tasked with measuring the ultimate tensile strength of a material…

A: To find: The ultimate tensile strength on the test. Given: The initial diameter of the rod, di =…

Q: A pressure cylinder has an outer diameter 210 mm, internal pressure 4.4 MPa, and maximum allowable…

A: Given Data

Q: What is the estimated flaw size responsible for the failure of a component made from silicon carbide…

A: Stress level = 250 MPaMaterial =  SiC

Q: rts are roller, and fixed Supports. Fig. 1. 21 (6) tang = tai

A:

Q: b-

A: GIVEN DATA A METAL PLATE IS GIVEN WE HAVE TO FIND ITS CENTRE COORDINATE X AND Y

Q: Material science Q1. Differentiate between true stress and enginnering stress and show them on…

A: Need to Differentiate between true stress and enginnering stress and show them on curve.

Q: How we can measure shear modulus?

A: The earth's material reaction to shear deformation is measured in shear modulus. The ratio of…

Q: Table 3 shows the fatigue data for a ductile cast iron to be used for an automobile axle that…

A: Given Data for ductile Cast iron Stress Ampitude (Mpa) Cycles to failure 740 1*101 604.8…

Q: Can someone rewrite the solution of this in a more readable and understandable way? thank you

A:

Q: Above figure provides steady-state operating data for a mixing chamber in which entering liquid and…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: What to do if the simulation result in Fusion 360 shows this (Screenshot attached)  Please provide…

A: Each thing has a stress limit that is determined by the material used in construction. A crucial…

Q: Give a specific example of positive reinforcement

A: Positive reinforcement is a technique that involves providing a stimulus to a behaviour after it…

Q: 4. To determine the upper and lower surface to beds ,we use. .type from ripple marks *

A: Given :-  To determine the upper and lower surface to beds ,we use ............type from ripple…

Q: A hemispherical dome of radius 40 feet is to be given 5 coats of paint, each of which is 1/100 inch…

A: Initial radius of the hemispherical domeThickness of the each coat of paint

Q: What do you mean by fixed cost and variable cost? Provide at least three examples of each item.

A: Fixed costs are expenses that do not vary with the level of production or sales. These costs stay…

Q: Discuss how you would create the solid model of the given objects.

A:

Q: You work for an off-shore wind turbine manufacturer and have been asked to review data from the…

A: Given data:The critical tensile stress must be 30 % more than the service stress of 420 MPa…

Q: -450.76 for parts (c) and (d) are incorrect.

A: To determine:c)The gauge pressure at point 2d)The gauge pressure at point 3

Q: Q3: What is the magnitude of true strain (e) if the true stress (o) is 15% larger than engineering…

A: Given data:- True stress=1.15×Engineering stress To find:- Magnitude of true strain

Q: Describe key stylized facts about both components of volume curve

A: The pressure-volume (PV) curve is a physiological tool that has been proposed for use in the…

Q: Q1a) A sample of an aluminum alloy has a tensile strength of 275 MPa, What will be the  maximum…

A: Tensile strength, is the maximum load that a material can support without fracture when being…

Q: a) Differentiate between Normal, Shearing and Bearing Stress.

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: /hat should be the degree of smoothness in systems with a uniform changing area.

A:

Q: Sketch a meat tenderizer mallet. And can you show me the measurement of it.

A:

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A:

Q: b) The elastic limit for some materials is difficult to determine exactly and so a yield point is…

A: Step 1: Step 2: Step 3: Step 4:

Q: Q12. (а) Differentiate between the "soft constraints" and “hard constraints

A: Constraint is something which imposes some kind of limit or restriction.

Q: You work for an off-shore wind turbine manufacturer and have been asked to review data from the…

A: Given data:The critical tensile stress must be 30 % more than the service stress of 420 MPa…

Q: What is the max circularity, on a radius, on the part below before a feature control frame is…

A: The tolerance of the part is

Q: Excel help if given the distance force and time how am to plot the force-deformation curve and then…

A: To plot a force-deformation curve in Excel from given data (distance, force, and time) and label the…

Q: a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with…

A: Given data as per question The stressσ in pipe varies jointly with the internal pressure(P) and the…

Q: A bimetallic strip (brass/steel), which is straight at room temperature, will be immersed in boiling…

A: