Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy= 200 MPa. The pin joints are constructed with sufficient size and fit to provide good resistance to out-of-plane bending. Determine the factor of safety for out-of-plane buckling. 800 mm where F= 1250 N 400 mm F The factor of safety for out-of-plane buckling is

Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy= 200 MPa. The pin joints are constructed with sufficient size and fit to provide good resistance to out-of-plane bending. Determine the factor of safety for out-of-plane buckling. 800 mm where F= 1250 N 400 mm F The factor of safety for out-of-plane buckling is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer for Part A, with THE CORRECT UNITS! Thank you Express your answer to three significant figures and include appropriate units.
¹Prob. 10.3-5. A square, tubular steel column has the di- mensions shown in Fig. P10.3.5, has a length of L = 3 m, and has an axial compression load of P = 50 kN. If the column has fixed-free end conditions and is free to buckle in any direction, what is the factor of safety with respect to elastic buckling? Let Est = 210 GPa and oy = 250 MPa. 125 mm 150 mm
Required information A short cantilevered round peg made from AISI 1030 cold-drawn steel is 40 mm in diameter and extends 10 mm from the wall. It is loaded, as shown, with a force F= 50 kN applied at the tip in the negative z direction and a torque T=800 N-m. The cross section at the wall is also shown, with points of interest A, B, and C. 10 mm 92 The minimum factor of safety is 2.93 Cross section at the wall Evaluate the state of stress at points A, B, and C, determine the critical case, and evaluate the minimum factor of safety based on the distortion-energy theory.
please explain in neat hand writing so I can undertstand
Can someone slove the fx and fy equations in the below questions solution in steps to how we got f1 and f2 values. Thanks.
- once answered correctly will UPVOTE!!
150- 18 F = 25 KN 25 200 25 + 25 € 100- -25 25 50 4 For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.
Problem 2 Assume that Member AB may be considered as long and slender and consider only Euler buckling. What is the critical Euler buckling load and will Member AB buckle? What is the factor of safety of the compressive load with respect to the critical buckling load? Assume buckling only occurs in the plane of the paper. Note: E-30e6psi, I-6.36e-3 in', A-2.83 in², LAB-41.6 in, FAB-540 lb (compression). Also Member OB is 36 inches (3 ft) long. F=270 lbf 3 ft 3 60 A = 45270 LB, n = 83.8, buckles 48400 LB, n = A. Per B. Per C. Per = 1088 LB, n 897, does not buckle 2.02, does not buckle D. Per = 544 LB, n = 0.993, buckles E. None of These
Sy= 296MPa please help solve and explain
A structural member in a nuclear reactor is made of a aluminium. An axial load of 22 kN is to be supported by the member. Use a factor of safety of 3.5 relative to yielding. EAl = 100 GPa, σy = 400 MPa. The material has elastic behavior. What is the load on the member if it is 1 mm long and its elongation is 0.5 mm?
A long, slender structural aluminum [E = 69 GPa] flanged shape is used as a l = 9.2-m-long column. The column is supported in the x direction at base A and pinned at ends A and C against translation in the y and z directions. Lateral support is provided to the column so that deflection in the x-z plane is restrained at mid-height B; however, the column is free to deflect in the x-y plane at B. Assume that b; = 102 mm, d = 122 mm, t; = 8 mm, and tw = 6 mm. Determine the maximum compressive load P the column can support if a factor of safety of 2.9 is required. In your analysis, consider the possibility that buckling could occur about either the strong axis (i.e., the z axis) or the weak axis (i.e., the y axis) of the aluminum column. bf C L Lateral B bracing L 2 A
Two parts of a machine, both made from steel, are held together by 5 equally-spaced M6 x 1.0 grade 8.8 bolts that are uniformly tightened to provide a total initial clamping force of 23 kN in the members. Each bolt has a proof stress of 600 MPa, and a tensile area of 20.1 mm². The elasticities are such that the joint constant is 0.2. A uniform static tensile load of 12 kN is applied to the entire joint after it has been preloaded. What is the magnitude of the total clamping force in the joint after the application of the tensile load? Express your answer in units of kilonewtons.