e wrenches to ensure that a bolt has a prescribed on when used for connections. If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm/mm, and leave a contact area on each head of 1.5 mm?, determine the tension in the bolt shank. The material has the stress-strain diagram shown. (Eigure 2) те 1) Express your answer to three significant figures and include appropriate units. < 1 of 2 T = Value Units The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. 3 mm Submit Previous Answers Request Answer < Return to Assignment Provide Feedback

e wrenches to ensure that a bolt has a prescribed on when used for connections. If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm/mm, and leave a contact area on each head of 1.5 mm?, determine the tension in the bolt shank. The material has the stress-strain diagram shown. (Eigure 2) те 1) Express your answer to three significant figures and include appropriate units. < 1 of 2 T = Value Units The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. 3 mm Submit Previous Answers Request Answer < Return to Assignment Provide Feedback

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ggg
A machine member is subjected to fluctuating stress O =0, cos(8 Tt). The endurance limit of the material is 350 MPa. If the factor of safety used in the design is 3.5, then the maximum allowable value of o, is ....... MPa (round off to 2 decimal places).
A machine element is subjected to loading as shown, assuming that load P is uniformly distributed across the section at which it is applied. The machine element has a uniform thickness of 20 mm. Two materials are considered: AISI 1020 HR steel and ASTM 25 gray cast iron. Determine the maximum safe load P if a factor of safety of 2.5 is specified for failure by slip for ductile materials and for failure by fracture for brittle materials. 15-тт radius 90-тт 60 тm 20-mm thickness 27-тm dia.
- once answered correctly will UPVOTE!!
What is the shear stress developed on the UPPER spring (in MPa)? What is the shear stress developed on the LOWER spring (in MPa)? What will the total elongation of the spring (in mm)? indicate the free body diagram
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
A ductile bar as shown in figure 1 has a yiel strength of oy = 390 MPa. Force F makes a 30° angle with the positive x axis. Deter- mined the magnitude of F that will cause yielding. Hint: Select the most loaded point in the structure and the failure theory to use according to the material (The standard one for this type of material). Refer to the lecture. 2 y 7 75 mm 500 mm F 300 mm X
An M5, coarse-pitch socket head cap screw with a nut is used to clamp together two 6 mm aluminum plates (E = 71 GPa). The fastener is 25 mm long and has an e of 209 GPa. What is the stiffness of the member in the clamped zone? Express your answer in units of N/um. Type your answer
15 M18 X4 Bolts F= 20 kN 60 D 60 |-75---75--| 50 250 A rectangular steelbar with 15 mm thickness attached to a 300 mm steel channelusing four tightly fitted bolts located at A, B, C, and D. For a F = 20 kN load find: (a) The resultant load on each bolt (FA, Fs, Fo, Fo=?) (b) The maximum shear stress in each bolt (T=?) (c) The maximum bearing stress occurred on the construction (OMAX=?) Note:All dimensions are given in mm unit.
A rod with diameter 12mm is initially measured and market at exactly 250mm apart. This material has an ultimate of 400MPa. After a tensile load applied, distance between the marks was measured to be 250.26mm. E= 200GPa Determine : A. strain of the rod stress in the rod. B. the stress in the rod C. the factor of safety for the situation
Part A A FA. FD= -600 mm- P 50 mm VE ΑΣΦ 41 B vec - 600 mm 25 mm If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 200 kN is applied. The assembly is made of A36 steel. (Figure 1) Enter your answer, separated by a comma. -0.15 mm D ? kN
If you are given the K and n values of two different materials, respectively. Is this information sufficient to determine which material is the tougher? also prove that at maximum load point, ɛ =nDo the proof only!