= 390 A ductile bar as shown in figure 1 has a yiel strength of oy MPa. Force F makes a 30° angle with the positive x axis. Deter- mined the magnitude of F that will cause yielding. Hint: Select the most loaded point in the structure and the failure theory to use according to the material (The standard one for this type of material). Refer to the lecture. N y 1075 mm 500 mm F 300 mm X

= 390 A ductile bar as shown in figure 1 has a yiel strength of oy MPa. Force F makes a 30° angle with the positive x axis. Deter- mined the magnitude of F that will cause yielding. Hint: Select the most loaded point in the structure and the failure theory to use according to the material (The standard one for this type of material). Refer to the lecture. N y 1075 mm 500 mm F 300 mm X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!
A copper tube with wall thickness of 8 mm must carry an axial tensile force of 175 kN. The allowable tensile stress is 90 MPa. The minimum required inside diameter is approximately: Match each item to a choice: d; Choices: : 90 mm : 80 mm : 75 mm : 65 mm 85 mm : 70 mm
Dr. (ny) A = 5.52 تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy === Sy (Neglect buckling) 600 kN 30 T 100 mm 600 kN Prepared by Dr. Hazim Khale anc dir the dia BC (b to ca th th n
A cylindrical steel bar 8 mm in diameter is loaded 1000 cycles per day with a load of 15560 N. How long until fatigue failure takes place? Note: stress force/area 500 450 400 350 Steel Allby 300 250 200 150 Brass Alloy 100 50 1.00E-07 Cycles to Failure, N 1.00E+04 1.00E+05 1.00E-06 1.00E+08 100E+09 1.00E+10 , The bar should not fatigue. ) The bar will fail in one cycle. ) 100 days ) 1000 days Stress Amplitude, MPa
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T = MPa
Find factor of safety if the Ultimate Stress of a ductile material is 250.94 MPa. If the material is subjected to a loading condition that generates the working stress of 151.27 MPa
* Question Completion Status: u(x) = N¡ ui + Ni+1 Ui+1 where: X1+1-X %3D and Ni+1 x-X Ix-+x Consider an element of length 1.85 (m) with node "" in origin. Consider a point at distance 0.33 L from the origin. Determine the value ofN1 for this point. QUESTION 19 Which failure criterion can be applied to brittle matenals? Select all applicable answers. O Tresca O Rankine All of the above OMises Submit to sqve and submit. Click Save AlILAnswers to save all answers.
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= 418.16 Use Hooke's Law to calculate the shear modulus of the specimen. answer: MPa G = i MPa
A machine component made of a ductile material is subjected to a variable loading with sigma min =-50 MPa and If the corrected endurance sigma max =50 MPa. limit and the yield strength for the material are sigma_{e} ^ prime =100 MPa and sigma_{y} = 300 MPa, respectively, what is the factor of safety ?
Required information Given a bar made of brittle material, properties of Sut= 30 kpsi and Suc = 90 kpsi and with stresses of Ox= -15 kpsi, Oy= 10 kpsi, and Txy=-15 kpsi. For the given state of plane stress, determine the factor of safety using the Coulomb-Mohr theory. The factor of safety is
The static shaft shown below is machined from aluminum 6082-T6. It is subjected to a static force of P=20 kN, T1=50 Nm, T2=50 Nm (Assume there is no buckling, Sut=240 Mpa, oy= 200 Mpa, E=70 Gpa). a) Find out the factor of safety using appropriate failure criteria. b) Determine the critical point(s) of the shaft -100 mm T2 d=20 mm P. T1