The five-bolt connection must support an applied load of P = 196 kips. If the average shear stress in the bolts must be limited to 13 ksi, what is the minimum bolt diameter that may be used for this connection? Part 1 There are 5 bolts. It is always assumed that each bolt supports an equal portion of the external load P. Calculate the force carried by each bolt. Answer: kips eTextbook and Media Save for Later Attempts: 0 of 6 used Submit Answer

The five-bolt connection must support an applied load of P = 196 kips. If the average shear stress in the bolts must be limited to 13 ksi, what is the minimum bolt diameter that may be used for this connection? Part 1 There are 5 bolts. It is always assumed that each bolt supports an equal portion of the external load P. Calculate the force carried by each bolt. Answer: kips eTextbook and Media Save for Later Attempts: 0 of 6 used Submit Answer

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.9P: Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For...

See similar textbooks

Similar questions

A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
Solve fast Include fbd. Urgent
Write legibly, provide step by step manual solution, and diagram for below given problem. An iron rod 6m long and 1.6mm2 in cross section stretches 1.2mm when a mass of 315kg is hang on it. Compute the modulus of elasticity of the iron. (Ans. E = 9656.72 Gpa)
IMPORTANT NOTE: PLEASE ANSWER PART 2 ONLY!! Answer in part 1: 2950.23N
Solve please
Kindly answer correctly. Please show the necessary steps
Don't Copy, I need correct solution within 10-20minutes. Please do it fast. [Handwritten recommended]
Two plates are clamped by a 3/4-10 UNC SAE Grade 5 bolt and regular nut with a 3/4-W plain washer as shown in figure. Top plate is made of grey cast iron and bottom plate is steel. An axial force of 12kN is acted upon the joint. Round off the length of the bolt to nearest 1/4in. Assume bolts are preloaded to 75% of proof load. 1. Determine the bolt stiffness kb. 2. Determine the member stiffness km. 3. Determine the yielding factor of safety of the bolt. 4. Determine the load factor for the bolt. 5. Determine the load factor guarding against joint separation. 1.25 in 1.00 in
Please solve all the question handwritten
A knuckle joint is used to connect two circular rods. The tensile force applied is 50 kN. The tensile stress in the rod and the shear stress in the pin are 25.46 MPa and 35.37 MPa, respectively. Determine the required diameter of the rod and the pin in mm.
Q4 The bolted connection in Figure 4 is subject to a tensile force F equal to 6353N, The plate A has a thickness of 14mm, and plate B a thickness of 25mm, Both plates have equal widths of 16mm. The bolt diameter is 4.06mm. Figure 4 B. P/2 B P/2 The yield strength of the plates is 116.7MPA Determine the bolt shear stress (Answer in MPa only). Determine the maximum axial stress (Answer in MPa only). Determine the maximum bearing stress (kPa). Determine the Factor of Safety for the plates. Determine the Factor of Safety for the bolt.
Needs Complete typed solution with 100 % accuracy. Don't use chat gpt or ai i definitely upvote you.