A simply supported shaft between bearings camies a steady load of 10 kN at the centre. The length of shaft between bearings is 450 mm. Neglecting the effect of stress concentration, find the minimum diameter of shaft. Given that Endurance limit = 600 MPa; surface finish factor= 0.87; size factor = 0.85; and factor of safety=1.6. [Ans. 35 mm]

A simply supported shaft between bearings camies a steady load of 10 kN at the centre. The length of shaft between bearings is 450 mm. Neglecting the effect of stress concentration, find the minimum diameter of shaft. Given that Endurance limit = 600 MPa; surface finish factor= 0.87; size factor = 0.85; and factor of safety=1.6. [Ans. 35 mm]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

hand written solution plzzz
For base case: N= 3500 rpm. D = 8 and 3/8 inch, Q = 400gpm, H = 280 ft, P = 41 hp, %3D Determine new Q. H, and P for |(a) when diameter is changed to 7" and speed is constant (b) when speed changes to 1750 rpm and diameter is constant (base case diameter)
What are the maximum, minimum, and average power values for the shaft shown in the figure below if the shaft speed is 50 rpm, l = 14 cm, a = 4 cm, b = 12 cm, P = 750 N, Tmin = -200 N-m, Tmax = 400 N-m.
A) A shat of diameter of d= 35 mm is subjected to a torque varying between 100 N.m to 500 N.m. The SCF due to keyway is 1.5, Su = 500 MPa, S', = 200 MPa. Correction factor for torsion=0.6. Surface finish factor=0.85 and size factor=0.82. Find the value of fatigue factor of safety F.S. Is the design of the shaft safe or not? And why?
Please design the following mechanical shaft targeting design objective of reliable structure and performance via design iterations with constrains of geometrical dimensions within performance requirement, safety, and economic factors (finding minimum material cost of suitable diameter). Notes: This shaft is transmitting 200 kW at 1200RPM. Please design the shaft with a suitable diameter via iterations, if the maximum torque transmitted exceeds the mean by 30%. Take maximum allowable shear stress as 70 MPa.
QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
A coupling GY8 is fixed on a shaft by a type C flat key, as shown in the figure. And the dimensions are also shown in the figure. The torque working on the shaft is 900N-m. [op]=100MPa. Please choose the dimension of the key and check its strength. op 27 = ×10³ kld 1. Note: Standard dimension series of flat key Diameter of shaft d >44-50 Width of key bx Height of key h 14x9 Length of key >75-85 >85-95 22x14 25×14 >50-58 >58-65 >65-75 16x10 18x11 20×12 6, 8, ..., 80, 90, 100, 125, 140, 160, 180, 200... Shaft 140 Coupling 70
Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the value of acceleration due to gravity g to be 9.81 m/s2, the value of y for carbon steel to be 76.5 x 103 N-m-3, and the value of Eto be 207 x 10⁹ N/m². NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. If the goal is to double the critical speed, what is the new diameter in mm? (You must provide an answer before moving to the next part.) The new diameter is mm.
a steam engine runs at 150rpm. its turning moment diagram gave the areas in mm2 taken in order above and below the mean torque line is 500,250,270,390,190,340,270,250, the scale for turning moment is 1mm=500mnm, 1mm=5’ if the fluctuation of speed is not to exceed +or-1.5% of mean, determine a suitable diameter and cross-section of the rim of flywheel with axial dimension equal to 1.5times the radial dimension. the hoop stress is limited to 3mpa and the density of material of flywheel is 7500kg/m3.
(8) An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r = 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). 6" (a) At the fillet, compute D and the 30 maximum tensile stress. (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?
There are two pairs of closed soft tooth surface spur gears A and B Parameters of A: modulus m = 2mm, number of teeth Z, = 40,Z, = 90, width of teeth b =60mm. %3D Parameters of B: modulus m = 4mm, number of teeth Z, = 20,Z, = 45, width of teeth b = 60mm. %3D The accuracy of the two pairs of gears is grade 8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason?