(8) An axle (non-rotating) is to be machined fromAISI 1144, OQT 1,000°F, to the proportionskeywayвshown, with a fillet radius r = 0.2D; F varies1.SDfrom 400 lb. to 1,200 lb.; the supports are tothe left of B, not shown. Let N = 2 (SoderbergLine).6"(a) At the fillet, compute D and the30maximum tensile stress.(b) Compute D at section B.(c) Specify suitable dimensions. Keepingthe given proportions, would a smaller diameter be permissible if the fillet were shot-peened?

Answered: Image /qna-images/answer/fe85076c-f5bf-4d8f-a451-f9e737e97380.jpg

An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r= 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). (a) At the fillet, compute D and the maximum tensile stress. 30 (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?

An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r= 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). (a) At the fillet, compute D and the maximum tensile stress. 30 (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 1: (P9, P10, M5, M7, D5) Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1=2880 N and T2-432 N. The maximum bending moment is at x =230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). 230 mm 280 mm 30-mm dia. 300 mm 250-mm dia. 400-mm dia. 270 N X. 1800 N
Perform double integration of the bending moment equations. You will obtain deflections in this form (can be found in the image attached) Calculate: the value of the constant integration C2. Enter your answer in kNm2 to three decimal places. b) the value of the integration constant C4. Enter your answer in kNm2 to three decimal places. c) the value of the deflection at point C. Enter your answer in mm to three decimal places.
Given the setup for cantilever beam. Solve for the following: a. b. C. d. Force at spring 1, KN Force at spring 2, kN Total deformation in m. Natural frequency, rad/s Frequency, Hz e. f. Period, s pt. A 3m pt. B 10m k12.06kN/m 10m pt. C m=50kg M= k2= 1.45kN/m 50kg
u need a table a-9 someone here has that as they answered my question before
Determination of vertical displacement of Mid-Term Project pipe assembly Find the vertical displacement at position C in the figure. 800 mm Pipe inner diameter: 40 mm, Pipe outer diameter: 60 mm Material: A-36 Steel 600 N B. -By the force 600N, the AB part of the pipe is subjected to bending and torsional loads. BC part is subjected to bending load. -The energy equation by this load is as follows. Energy equation by torsional load: 400 mm T²dx (U), = 2GJ Problem: Energy equation by bending load a) First, draw a free body diagram and the AB part Of the bending/torsional load of the BC and Derive the bending load equation. So M²dx (U) = 2EI By applying it to the high energy formula, Save energy and make it the same as external energy Release to find the vertical displacement. -The sum of the internal energy of 2 energy is as follows. U=U: +Ub b) Creo modeling and structural analysis -Due to energy conservation, the sum of the internal energy U is the external due to the load 600 NGet the…
A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 10 in a length of 26 diameters. Compute the proper diameter if G = 83 GPa. [Note: Attach your solution] %3D
Solve
I need the answer quickly
Solve A and B
Do in 3 min
Design