Question 2: A reducing elbow is used to deflect water flow at arate of 30 kg/s in a horizontal pipe upward by an angle 0 = 45°from the flow direction while accelerating it. The elbowdischarges water into the atmosphere. The cross-sectional areaof the elbow is 150 cm² at the inlet and 25 cm² at the exit. Theelevation difference between the centers of the exit and the inletis 40 cm. The mass of the elbow and the water in it is 50 kg.Determine the anchoring force needed to hold the elbow in place.Water150 cm²25 cm²45°40 cm

Step 1:Given:- Mass flow rate (m˙)=30kg/s- Inlet cross-sectional area (A₁)=150cm²=0.015m²- Exit…

Answered: Question 2: A reducing elbow is used to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6-22 A 90° elbaw is used to direct water flow at a rate of 25 kgis in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03. 35 cm Water 25 kg/s
Air enters through a duct of a fan with a velocity of 4m/s and an inlet pressure of2cm of water less than atmospheric pressure. The air leaves the fan through aduct at a velocity of 12m/s and a discharge static pressure of 8cm of waterabove atmospheric pressure. If the specific weight of air is 1.2kg/m3 and the fandelivers1 2m3/s, what is the fan input power to the motor if the fan has amechanical efficiency of 70% and motor efficiency of 80%.
A reducing elbow is used to deflect water flow at a rate of 30 kg/s in a horizontal pipe upward by an angle 0 = 45° from the flow direction while accelerating it. The elbow discharges water into an atmosphere. The cross sectional area of the elbow is 150 cm² at the exist. The elevation difference between the centers of the exist and the inlet is 40 cm. The mass of the elbow and the water is 50 kg. Determine the anchoring force needed to hold the elbow in place. (Ans: 1.18 kN) 150 cm 40 cm Water
A reducing elbow in a horizontal pipe is used to deflect water flow by an angle ? = 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross- sectional area of the elbow is 150 cm2 at the inlet and 25 cm2 at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 50 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentumflux correction factor to be 1.03 at both the inlet and outlet.
The figure below shows a turbine with an inlet pipe and a draft tube. If the efficiency of the turbine is only 80 percent and the discharge of the water is 1000 litres per second. Calculate: (a) the power developed by the turbine: (b) The reading of the gauge G:
(b) A reducing elbow is used to deflect water flow at a rate of 30kg/s in a horizontal pipe upward by an angle of 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross sectional area of the elbow is 150 cm? at the inlet and 25 cm? at the exit. The elevation difference between the centres of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 50 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum-flux- correction factor to be 1.03. 25 cm? 45° 150 cm? 40 cm Water
not an assingment or assesed question its a tutorial
kg Water (p = 1000- -) flows through the elbow below. The diameter of both the inlet and outlet is 1.1 cm, and the velocity through the nozzle is V =4.5 m/s. The outlet m³ has an angle of 0 =15 degrees. The water is at a pressure of 29 kPa (gauge). Find the magnitude of the force on the elbow. 0 V
A reducing elbow in a horizontal pipe is used to deflect water flow by an angle 8= 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm2 at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 56 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03 at both the iniet and the outlet. The density of water is 1000 kg/m³, and the flow rate of water is 30 kg/s. Waters 30.0 kg/s 150 cm- 25 cm² 45° 40 cm The anchoring force needed to hold the elbow in place is The resultant direction of force is KN
Water (p = 1000 kg m3'H= 10-3 R) flows in a horizontal constant-area pipe; the pipe cross ms 1. section area of 0.1 m?. At the pipe inlet, a pump is installed and at the outlet, the pressure is atmospheric. Determine the pump power when the pipe length is 10 meter and a. When the velocity is 0.01 m/s b. When the velocity is 0.1 m/s and the pipe is smooth When the velocity is 0.1 m/s and the pipe equivalent roughness is 0.1 mm (you may use Moody chart here) d. When the pipe is smooth and vertical and the velocity is 0.1 m/s С.
A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate m of 37 kg/s. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the density of water to be 1000 kg/m³ and the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. Water m kg/s O 50 cm Determine the anchoring force needed to hold the elbow in place. The anchoring force needed to hold the elbow in place is The resultant direction of the force is 155 429 N.
The Water is flowing through a pipe having diameter 350 mm and 210 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 25.85 N/cm? and pressure at the upper end is 11.6325 N/cm? & the rate of flow through the pipe is 40 lit/s. Draw a neat diagram and determine the following: 1.Velocity head at bottom of the pipe in m/s. 2. Velocity head at top of the pipe in m/s. 3. The difference in datum head between top & bottom in meter of water - 4. The difference of pressure head between bottom to top end in meter of water.- The velocity of flow of water at the bottom in m/s.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS