A fireman standing on the ground with a firehose in his hands attached to a hydrant . The density of the water is 1000kg/m^3. What is the velocity of the water out of the hose given the following data Abs. water pressure in the hydrant(Pa) 275,000 Water velocity out of the hydrant (m/s) 10.5 Atmospheric Pressure (Pa) 101330

A fireman standing on the ground with a firehose in his hands attached to a hydrant . The density of the water is 1000kg/m^3. What is the velocity of the water out of the hose given the following data Abs. water pressure in the hydrant(Pa) 275,000 Water velocity out of the hydrant (m/s) 10.5 Atmospheric Pressure (Pa) 101330

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Total pressure port (in) Static pressur ports N - 9800, and density of gas m Total (out) Coaxial pressure A pitot-static pressure probe (see Fig. 9.28, and the equations above it) inserted within a large duct with a flowing stream of an atmospheric gas indicates an equivalent pressure deflection of 5.7 cm H₂O. What is the speed of the gas measured in meters/sec? Assume that the specific weight of water 1.10k. Round your answer to the nearest m 2 (two) decimal places. Watch units carefully!
please help me with these questions ,i will be very very appreciate!!!!Please do not copy other's work
400mm Kerosene, SG=0.82 Air, SG=0.0012 Benzene, SG= 0.88 100mm 200rim 150mm 90mm Water Hg What is the pressure difference between the pipes of air and benzene?Use SG of mercury as 13.6.
Suppose we got the following data during a test of a 2- stroke engine in which gas is usedas a fuel:Diameter of the piston = 149 mmStroke length = 179 mmClearance volume = 0.88 literrpm of the engine = 302Indicated mean effective pressure = 6.0 barGas consumption = 6.0 m3/hCalorific value of the gas (fuel) = 16990 kJ/m3Make a clear sketch the geometry of this engine using the data and determine thefollowing:i. Indicated power developed by the engine in watt.ii. Air Standard Efficiencyiii. Indicated thermal efficiency of the engine.
Can yu please complete question 4
Please show complete given, required, schematic diagram, solution and discussion. Show all the formulas used and don't round off.
A Large wind turbine has blade span diameters of 110 m. It sits high off the ground where the average wind speed is 7 m/s. Assume the air density to be 1.25 kg/m3, and the efficiency of the wind turbine, its generator and its electric grid synchronization device is 26%. What is the average electric power that this turbine can output to the grid? a. Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
From the provided pump table: 1. Calculate the power required at the pump shaft given that the water density and flow rate are 1000kg/m³ and 400L/s respectively. <-- Do this calculation in the same excel file as the graph 2. Construct a Q – H and Q– n curves of this pump on one graph. <-- Attach an Excel file of your graph using the link below. Units are required and will be marked. n (%) H(m) Q (m/s) 56 0.000 25 55 0.010 45 54 0.020 60 52 0.030 64 49 0.040 62 42 0.050 48 34 0.060 32 20 0.070 18 8 0.080
QUESTION 35 A syringe (X), forces air, at a high velocity, over a straw (Y). The air in the water chamber (Z) is not moving. Using Bernoulli's Principal, pick the best answer, that describes what will happen to the water in the chamber. Remember that things are always pushed from high pressure areas to low pressure areas. a. The high velocity air at (Y) will have the SAME PRESSURE as the low velocity air over the water at poing (Z), so the water will neither move up or down the straw. b. none of these are true. c. The water in the straw will be forced down into the chamber because the high velocity air at (Y) has a HIGH PRESSURE compared to the air over the water in the chamber at point (Z). d. The high velocity air at point (Y) will have a LOW PRESSURE. As a result, the slow air in the chamber (Z) will have a high pressure, thus forcing water up the straw.
Assemble and describe the operation of a simple piping system (with only one branch, or at most two branches) for the industrial process of alcohol and sugar. Use the following equipment: Pumps, valves, heat exchangers, pressure gauges, flow meters, elbows and flanges For this system, what would be the most appropriate pressures and flows?
Q No. 5: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure gauge at discharge reads 30 psi and vacuumed gauge at intake reads 10 inches of Hg. If Q=3cfs of water and the brake horsepower is 35. Find the efficiency of the pump. There are no losses. Note : Please Solve as Per Question's Statement. Need a Neat and Clear Solution.See Attached Picture For Detail .
The system curve for a water supply system is shown in the figure below (i.e., red curve). If a 7-inch pump is operating at 1160 rpm, what will be the discharge of water through the system in GPM? Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 HEAD IN FEET 30 25 W 20 10 5 L/SEC 5 7.00" (178mm) 6.75" (171mm) 6.50" (165mm) 15 6.25" (159mm) 7.25" (184mm) O 150 GPM Laco O 350 GPM O 450 GPM O 250 GPM 10 Model 4075 FI & CI Series 15 70% 20 "Dede de 088 A. 25 REQUIRED NPSH 90 1160 RPM November 1, 2010 TM 90- N 00 30 8800 877 1HP(.75KW) de (5 60% ox 35 -10% 5% Tolo 10. 3HP(2.2KW) 2HP(1 5KW). 15HP(1 1KW). CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE 45 LOWONG FEET 15 12 9 6 0 6 5 + 2 1 750 NPSH HEAD IN METERS 45 36 OG KPO 27 18 -9 -70 -60 -50 -40 20 10 -0 HEAD IN KILOPASCALS