Example (7): Determine the heating surface area required for the production of 2.5kg/s of 50wt% NaOH solution from 15 wt% NaOH feed solution which entering at 100 oC to a single effect evaporator. The steam is available as saturated at 451.5K and the boiling point rise (boiling point evaluation) of 50wt% solution is 35K. the overall heat transfer coefficient is 2000 w/m²K. The pressure in the vapor space of the evaporator at atmospheric pressure. The solution has a specific heat of 4.18kJ/ kg.K. The enthalpy of vaporization under these condition is 2257kJ/kg Example (6): 5:48 م An evaporator is concentrating F kg/h at 311K of a 20wt% solution of NaOH to 50wt %. The saturated steam used for heating is at 399.3K. The pressure in the vapor space of the evaporator is 13.3 KPa abs. The 5:48 O

Example (7): Determine the heating surface area required for the production of 2.5kg/s of 50wt% NaOH solution from 15 wt% NaOH feed solution which entering at 100 oC to a single effect evaporator. The steam is available as saturated at 451.5K and the boiling point rise (boiling point evaluation) of 50wt% solution is 35K. the overall heat transfer coefficient is 2000 w/m²K. The pressure in the vapor space of the evaporator at atmospheric pressure. The solution has a specific heat of 4.18kJ/ kg.K. The enthalpy of vaporization under these condition is 2257kJ/kg Example (6): 5:48 م An evaporator is concentrating F kg/h at 311K of a 20wt% solution of NaOH to 50wt %. The saturated steam used for heating is at 399.3K. The pressure in the vapor space of the evaporator is 13.3 KPa abs. The 5:48 O

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Question attached
Typical head pressures should correspond to a condensing temperature_________ F higher than room temperature at design operating conditions. A. 5-10 B. 10-15 C. 20-35 D. 35-45
26. NA 25-g ice cube at 0.0°C is heated. After it first melts, the lemperature increases to the boiling point of water (100.0°C). and the water then boils to form 25 g of water vapor at 100.0 C. How much energy in total is added to the ice/water? Which Process (melting, increasing temperature, or boiling) requires e most energy? Water has a latent heat of vaporization of specific heat of 4190 J/(kg · K). fon ice cube of mass
A water tube boiler produces 250,000 pounds of steam per hour at 1200 psia and1000OF from feed water entering the boiler at 1500 psia and 360oF. Fuel oil havinga higher heating value of 18,200 Btu/lb is supplied to the burners at the rate of20,700 lb/hr. Furnace volume is 1500 cubic feet. Calculate the equivalentevaporation, lb/hrA. 300,117 B. 300,317 C. 300,517 D. 300,717
Heat-Transfer Coefficient in Single-Effect Evaporator. A feed of 4535 kg/h of a 2.0 wt % salt solution at 311 K enters continuously a single-effect evaporator and is being concentrated to 3.0%. The evaporation is at atmospheric pressure and the area of the evaporator is 69.7 m². Saturated steam at 383.2 K is supplied for heating. Since the solution is dilute, it can be assumed to have the same boiling point as water. The heat capacity of the feed can be taken as cp = 4.10 kJ/kg · K. Calculate the amounts of vapor and liquid product and the overall heat-transfer coefficient U. 8.4-1.
A CHIMNEY OF 24m HEIGHT IS USED TO PRODUCE A NATURAL DRAUGHT WHEN FLUE GAS TEMPERATURE IS 300°C AND AMBIENT TEMPERATURE 25C.THE AIR SUPPLIED IS 20K|kg OF FUE BURNED FIND THEORETICAL DRAVGHT PRODUCED IN mm of WATER.
A distillation column with a total of 13 actual stages (including a partial condenser) is used to perform a separation which requires 7 ideal stages. Calculate the overall column efficiency, and report your answer in %
Steam is to be condensed by direct injection of cold water. The steam enters the condenser at the rate of (450 kg/hr) with dryness fraction of (0.9) and pressure (1 bar). The estimated heat losses from the condenser to the surroundings is (8500 kJ/hr). If cold water enters at (15"C) and the mixture of condensate and cooling water is to leave at (95"C). Determine the required flow of cooling water.
Example (2): a 5400 kg/hr of steam is supplied by a certain boiler plant at pressure (750 kPa) and dryness fraction 0.98. Feed water is supplied at a temp. (41.5°C). The mass of fuel (coal) is (670 kg/hr) with L.C.V = 31000 kJ/kg. Determine: a) The boiler efficiency. b) The equivalent evaporation E.E. at 100°C. c) The saving in coal per hour if the economizer is fitted in the flue gases (the feed water temp. can be raised to 100°C), assuming the other conditions are the same.
What is entropy? Write entropy equation. What happens to the entropy in ideal isobaric heatingprocess? Show this process on Pv and Ts diagram.
Please show the coimplete solution. (Example: Conversion of Units) In an ammonia condensing machine (Compressor Plus Condenser) the water used for condensing is 55°F and the evaporator is at 15°F. Calculate the ideal COP.
a) the local film condensation heat-transfer coefficient at the bottom of the tube b) the average condensation heat-transfer coefficient over the entire length of the tube c) the total condensation rate at the tube surface.