Water flows through a circular pipe with a 180° horizontal elbow and exits to the atmospherethrough a nozzle as shown in figure 3. The diameter of the pipe is 300mm and the diameter of thenozzle exit is 160mm. The density of water is 999kg/m³. The mass flow rate of water is 140kg/s.Incompressible, inviscid flow may be assumed.section 2$ 160 mmRx$ 300 mmsection 1Figure 3: defaulta. Calculate the velocity of the water at sections 1 and 2 respectively,Xb. What is the gauge pressure at section 1?C. What is the magnitude and direction of the force Rx exerted by the water on the elbow?

Answered: Water flows through a circular pipe…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Water flows steadily through a smooth, circular, horizontal pipe. The discharge rate is 1.5 ft3/s and the pipe diameter is 6 in. Find the difference in the pressure between two points 400 f t apart if the water temperature is 60°F. 2. A 2000-gallon swimming pool is to be filled with a 0.75 in. diameter garden hose. If the supply pressure is 60 psig, find the time required to fill the pool. The hose is 100 f t long, with a friction factor equal to 0.02.
Solve all parts where density of fluid is 900kg/m3
could you please help me calculate the maximum height of the jet , Hj in metres please
Solve all question.
1.1 A 6 inches pipe carrying 3.93 cfs connects to a 6 inches pipe. Find the velocity head in the 6 inches pipe. 1.2 Sulfur dioxide flows through a 12 inches discharge duct that reduces to 6 in diameter at discharge into a stack. The pressures in the duct and discharge stream are. respectively, 30.0 psi absolute and atmospheric (14.7 psi). The velocity in the duct is 50.0 ft/sec, and the temperature is 80 F. Calculate the velocity in the discharge stream if the temperature of the gas is 23 F. 1.3 Water flows through a horizontal 100-mm pipe under a pressure of 414 kPa. Assuming no losses, what is the flow if the pressure at a 75-mm diameter reduction is 138 kPa?
3). in the figure below. Consider the acceleration due to gravity as g=32.2 ft/s², specific weight of water as yw-Pwg=62.4 lb/ft³ and gasoline as ygasoline=Pgasolineg=42.5 lb/ft³. What pressure, pi, is needed to produce a flowrate of 0.09 ft³/s from the tank shown Air Gasoline 2.0 ft Salt water 3.6 ft SG = 1.1 0.06-ft diameter -
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
find Step 1: Known, UnknownStep 2: SchematicStep 3: FormulaStep 4: CalculationsStep 5: Discussion A 30 cm diameter pipe, conveying water, branches into two pipes of diameters20 cm and 15 cmrespectively. If the average velocity in the 30 cm diameter pipe is 2.5 m/s, find the discharge inthis pipe (m3/s). Also determine the velocity (m/s) in 15 cm pipe if the average velocity in 20cm diameter pipe is 2 m/s.
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
In car service station water flows through a vertical pipe reduced from a pipe of diameter D to another diameter 0.5 D. The flow velocity at the inlet to the contraction is 2 m/s and pressure is 20N/cm2 if the height of the contraction measures 2m, what is the pressure at the exit of the contraction? Draw diagram neatly.
Oil flow through a 16 tubes on a single cooler with a velocity of 2 m/s. The internal diameter of the tube is 30mm and oil density is 0.85 gm/ml. Find the volume flow in liters per sec.
A horizontal Venturi meter is shown in Figure 8 to measure the flow rate of water in the mainpipe. The main pipe area and the throat area are 100 m2 and 50 m2 respectively. The pressureP1 is measured as 3000 kPa and the pressure in the throat is P2 = 50.0 kPa and assume, thedensity of water is 1000.0 kg/m3. Use Bernoulli’s Principle to: a) Determine the velocity V2 , m/s in the throatb) Determine the velocity, V1, m/s in the main pipec) Determine the flow rate Q, m3/s in the water mains.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS