For the siphon shown in figure (2), calculate (a) The mass flow rate of water from the tank and (b) The pressure at point C, Use the last two digits of your ID for the height L_ in cm 75 Ignore losses 1.2 m B D A Pipe 40-mm inside diameter 1.8 m Flow 25-mm diameter F L cm

For the siphon shown in figure (2), calculate (a) The mass flow rate of water from the tank and (b) The pressure at point C, Use the last two digits of your ID for the height L_ in cm 75 Ignore losses 1.2 m B D A Pipe 40-mm inside diameter 1.8 m Flow 25-mm diameter F L cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show complete solution. Units must be included in all calculations. All numerical values should be rounded off to the nearestthousandths. 3.At section 1 of a pipe system carrying water the velocity is 3.0 fps and the diameter is 2.0 ft. At section 2 thediameter is 3.0 ft. Find the discharge and velocity at section 2.
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
Calculations involving retention time involve the following formula, T =, where V is volume and Q is flow rate. Often times, you will be required to calculate the volume of more than one tank and determine a rate of flow, given a total retention time. Tank 1 Tank 2 Let's assume that the total retention time for the entire system is 55 minutes, and we want to know the inlet flow, given the dimensions of tank 1 are : 14m x 10m x 3 m, and tank 2 are: 5m x 10m x 3 m. Calculate the inlet flow.
Shown below is a performance data for a water pump. For each row of data, calculate the pump efficiency (percent). Estimate the best efficiency point (%) and the volume flow rate (gpm) and net head (ft) at the best efficiency point. gpm ft KW 200 75 4.9 300 73 6.7 400 71 7.2 500 66 8.1 600 60 9.0
water flows through 30 mm internal diameter pipe at atmospheric pressure. pitot tube measures the velocity of water at the center of pipe as shown in the fig. the pressure difference between the impact tube and the static tube is 20cm of carbon tetrachloride (density: 1600 kg/m³). calculate the volumetric flow rate through the pipe in cubic meter per hour. velocity of water is cp.
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Po = 673 kg/m) 05 m 95 kPa 100 kPa Pump
Air flows thru a device shown in the figure below. If the flow rate is large enough, the pressure within the constriction will be low enough to draw the water up into the tube. The specific weights of water and air are 9.80 and 12 KN/m3, respectively. If frictional loss is neglected, compute the following: a) the pressure of air at point 2 (kPa), b) the flow rate (L/s), and c) the pressure needed at section 1 to draw the water into section 2 (kPa). Note: Maintain up to 3 decimal places on partial and final answers.
Water is flowing steadily at an average velocity of 6 m/s in a pipeline of diameter 50 mm. Somewhere along the pipeline, the diameter of the pipeline is reduced by a fitting to a diameter of 20 mm. Calculate the average velocity of flow in the 20 mm diameter section of pipe. [Answers in m/s, Numerical value only] Answer: Next page OSearch for anything
The figure shows a system in which water flows from a tank through a system of pipes that have various sizes and heights Determine: a) The gauge pressure at points A, B, C, D, E, F, G. b) The velocity at points A, B, C, D, E, F, G. c) Construct a diagram showing the line of total energy (L.E) and the line of mechanical height (L.A.M)
3. A seamless steel pipe carries 2000 m³ of steam per hour at a pressure of 1.2 N/mm². The velocity of flow is 28 m/s. Assuming the tensile stress as 40 MPa, find the inside diameter of the pipe and its wall thickness. [Ans. 160 mm; 5.4 mm] 4. Compute the dimensions of a flanged cast iron pipe 200 mm in diameter to carry a pressure of 0.7 N/mm².
The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Pol = 673 kg/m) %3! 0.5 m 95 kPa 100 kPa Pump