what will be the expected reading h in the mercury manometer in meters? SAE 30W oil at 20°C flows through a 9-cm-diameter pipe as shown in thediagram at an average velocity of 3.2 m/s. For SAE 30W oil, p = 891 kg/m³and μ 0.29 kg/(m·s).VD=9 cmSAE 30W oilh2.5 mHg

Answered: SAE 30W oil at 20°C flows through a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
Fluid mechanics
solve the question in the image provided.
How can i find the volume flow rate in m3/s
The narrow section of a nozzle is 8 cm in diameter. While the fluid passes through the nozzle at a volume flow of 12 m3 / hour, the pressure difference was measured as 0.05 mSS. In this case, what is the flow rate coefficient (K) of the nozzle? (ρ = 1000 kg / m3, g = 9.81 m / s2) a. 0.623 b. 0.672 c. 0.752 d. 0.642 e. 0.585
Find the volume flow rate and direction of a certain fluid flowing in a tube system as shown below. 2 8 10 Flows in cm³/s 1.01 4 in O 2; in O 2; out Cannot be determined; insufficient information. O 1; out
(1) Basic Concepts Show that a stress and a momentum flux have the same unit by showing that a force and the rate of momentum change or transfer have the same unit. (2) Overall Mass Balance Equation An incompressible fluid is flowing through a circular conduit, as shown in the figure below Fig P1.2-1. The velocity profile of the fluid in the 8-cm-diameter pipe is v, = 0.1 ст/s What is the average velocity in the 2-cm-diameter pipe? 2cm 8cm Tube (3) Overall Momentum Balance Equation Ahorizontal turbulent liquid jet of diameter Dand average velocity v, impinges on a vertical plate mounted on a cart, thus exerting a force F on a plate, as shown in Fig. P1.4-3. Determine the opposing force needed to keep the plate moving at a constant velocity v, (< v). Neglect the viscous and gravity forces. (Hint: Let the control volume Q move with the plate) Plate Nozzle 1|Page (4) Differential Momentum Balance Equation Consider the incompressible Newtonian fluid flowing, under the pressure gradient…
pls replyyy Air is flowing through a square conduit whose section changes from 100 mm (section 1) to 200 (section 2). At section 1, v1=6 m/s and the density at section 1 is 1 kg/m3. If the velocity of flow is 1.8 m/s at section 2, find the density of gas at section 2
During a trip to the beach (Patm = 101 kPa), a car runs out of gasoline (density is 750 kg/m^3), and it becomes necessary to siphon gas out of another nearby car to a tank of a volume of 4 litres using a hose whose cross-sectional area is 0.2 cm^2. The shown setting is used where L1=0.7 m and L2=2.2 m. Consider point 1 to be at the free surface of gasoline in the tank so that P_1= 1 atm, V_1 ~= 0 since the tank is large relative to the tube diameter. Consider the gravitational acceleration to be 9.81 m/s^2. Using Bernoulli equation, the pressure at point_3 in kPa is: Select one: O a. 72.55 Z3 Ob. 122.34 Gasoline OC. 79.66 siphoning tube L2 Gas tank L1 22 Gas can/
In fluid mechanics, The minor losses occur due to any disturbance that might occur to the flow, which is mainly caused by the installed fittings on the pipeline. Why does the coefficient of minior loss decrease with increasing flow rate?
A Pitot tube on an airplane flying at standard sea level reads 26kPa. What is the velocity of the airplane (in m/s)? Assume that psea-level = 1.3 kg m O 100 O 200 400
(1) Given the working form of the Bernoulli equation as dW - F dm Where 3 is the friction heating per unit mass dP F = Au - dm Given also that friction heating in laminar flow of Newtonian fluids in circular pipes is given as -AP F =- = -gAz = Q Ax " 128 Ax is change in the x-direction. A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometer

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

SAE 30W oil at 20°C flows through a 9-cm-diameter pipe as shown in the diagram at an average velocity of 3.2 m/s. For SAE 30W oil, p = 891 kg/m³ and μ 0.29 kg/(m·s). V D=9 cm SAE 30W oil h 2.5 m Hg