How do I solve this task A weight for a lift is suspended using an adapter. The counterweight is held up with 4 screws. The weight F is 3200kg. The screws have a strength class of 8.8. Safety factor 3 Which is the smallest bunch size that can be used?+_Sr/Fm =0,16Gr=0,71ơ=800·0.8=640 MPaAs=?Fmax= As·ơ·GrFs=ơs·AsFFm= Fs· GFSF =SF / FFm · FFm Fpreload =Fload / SF → Fload /3Fpreload per screw =Fload / SF → Fload /4As=Fpreload per screw /ơ·Gr → As= Fpreload per screw / 640· 0.71 The correct answer should be M12 with As=84.3mm²

How do I solve this task A weight for a lift is suspended using an adapter. The counterweight is held up with 4 screws. The weight F is 3200kg. The screws have a strength class of 8.8. Safety factor 3 Which is the smallest bunch size that can be used?+_Sr/Fm =0,16Gr=0,71ơ=800·0.8=640 MPaAs=?Fmax= As·ơ·GrFs=ơs·AsFFm= Fs· GFSF =SF / FFm · FFm Fpreload =Fload / SF → Fload /3Fpreload per screw =Fload / SF → Fload /4As=Fpreload per screw /ơ·Gr → As= Fpreload per screw / 640· 0.71 The correct answer should be M12 with As=84.3mm²

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.9P: A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in....

See similar textbooks

Similar questions

A lift with a counterweight is attached to the ceiling. The attachment is with 6 stainless and oiled screws. What screw size is required? What tightening torque? - The lift weighs 500 kg and can carry 800 kg. - Counterweight weight 600 kg - Durability class 12.8 = 960 MPa- Safety factor ns=5+-Sr/Fm= 0.29Gr =0.55
The adjustable height caster is designed to carry 2000 N and operate on the floor that may not be flat. The spring must give sufficient force to keep the wheel touching the floor. A bolt M8x1 is used to adjust the height of the caster. Find the minimum number of thread (t) on nut that made of steel having tensile strenght of 400 MPa considering the factor of safety is 3. F spring Number of thread t = To select a suitable spring from catalog, you need to find the spring rate (spring constant) providing that the free lenght of the spring is 40 mm and the spring will be assembled around the bolt. Compression spring specification can be found in CSC spring catalog on page 12-228)
60 l all ۱۲:۰۱ ص EQUILIBRUIM2&3D.pdf -> supporte ny pan connection at A and fixed pin in smooth slot at B. Load L Figure 3/A Page5 3/B In each of the five following examples, the body to be isolated is shown in the left-hand diagram, and either a urang or an incomplete free-body diagram (FBD) is shown on the right. Make whutever changes or addi tions are necessary in each case to form a correct and complete free-body diagram. The weights of the bodies ure negligible unless otherwise indicated. Dimensions und numerieal valueu are omitted for aimplicity. Body Wrong or Incomplete FBD 1. Lawn roller of mare m being do paesnd incline e. 2. Prybar lining body A having smooth horizantal surface. Bar reste on horizontal rough surface. 3. Unifarm pele of mass w being hoisted into po i- tion by winch. Hariaontal aup- porting surface Totohed to prevent slipping of pale. mg Notrh 4. Supporting angle bracket for fnime; Pin joints 5. Bent rod welded to upport at A ond subiected ta two forc and…
The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6 and the rivets are made from aluminum 2014-T4. Evaluate the maximum allowable force on the connection to meet the following design critoria the shoar stross in a rivot cannot excced 1/4 of the ultimate strongth in shoar. 75 mm 38 mm 38 mm 12 mm dia -9 mm The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6 and the rivets are made from aluminum 2014-T4. Evaluate the maximum allowable force on the connection to meet the following design criteria the tensile stress in the plates cannot exceed 1/3 of the yield strength. mm 75 mm 38 mm 38 mm 12 mm dia. The figure below shows two plates connectd by two rivets. The plates are made from aluminum 6061-T6 and the rivets are made from aluminum 2014-14. Evaluate the maximum allowable force on the connection to moet the following design criteria the bearing stress on either the plates or the rivets…
or the spring system given in Figure 1, create the clement matrices as well as the global stiffness and force matrix, note that k-1. -ww- Figure 1
Need only handwritten solution only (not typed one).
Please help provided all that is needed, all analysis etc. Thank you
How do I find the axial forces on this countershaft? Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side.
part 3 please
To calculate the maximum axial loads for a column based on yielding and buckling about both axes, and allowing for factors of safety. The critical load P for buckling of a column depends on the vertical distance between supports and how the column is connected to those supports. The length L in the T'EI formula Per =- is the distance between points of zero moment. For a pin- L2 supported column, this is the full height of the column. For a column that is not pinned at both ends, the points of zero moment are not at the supports. The equation for the critical load can be modified to use an effective length Le = KL, where K depends on the support conditions. For a column fixed at both ends, K = 0.5. For a column fixed at one end and pinned at the other, K = 0.7 (Figure 1). The equation for the critical load then becomes ’EI Pa (KL)²
part 4 please
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?