1 Nuts installed on a piece of all-thread experience the following forces in serviceFB3.5 kip 5.75 kip 0.85 kipFDFc1.4 kipFAThe length of each segment is given by:ab.4 in13 in 7 inIf the all-thread is composed of a material that has an elastic modulus of 31000 ksi, and its effective diameteris 0.7 inches, determine the following(a) The maimum normal stress in this piece of all-thread.(b) The change in length of segment AB.(c) The change in length of segment BC.(d) The change in length of segment CD.(e) The change in length of the whole length of all-thread.Under the following assumptions:Bearing stress between threads of the allthread and the nut may be neglectedStress concentration effects may be neglected• The forces that the nuts apply may be treated as concentrated forces at each location• The nuts may be treated as rigid.• The force applied to each nut is distributed evenly around the nuf's perimeter.(a) oma(b) SAB=(c) Snc(d) deD(e) tal• be sure to include units with your answers• denote tensile stresses and elongations with positive values compressive stresses and compactions withnegative values

lets consider the screw into three segments area of all threadA=π4×0.72A=0.384in2

Answered: Nuts installed on a piece of all-thread…

Nuts installed on a piece of all-thread experience the following forces in service FA Fg Fc FD 3.5 kip 5 75 kin 0 85 kin 14 kin

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

We will use both shearing and bearing analysis to determine the quantities of rivets needed to fasten BC and BE. We can determine two values then choose what will be more safe. ■ For Member BC: ■ Based on Shearing: V T == ■ Av Based on Bearing: P Ab 70MPa = 96000 N .n. (19) ²x n 1/4. π n = 4.84 5 rivets 96000 N (19mm) (6mm) xn 140MPa n = 46.015≈ 7 rivets For member BC, we must use 7 rivets since we must need a minimum of 7 rivets to resist bearing stress produced by the connection. If we only use 5 rivets, then the bearing stress will become 168.42 MPa. It will result to failure since the allowable bearing stress is only 140 Mpa. ■ For member BE: (Practice at Home) Pac EXAMPLE: 5. The figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm diameter rivets are required to fasten member BC to the gusset plate? Member BE? What is the largest average tensile or compressive stress in BC and BE? Say…
PLEASE ANSWER IT CORRECT I WILL UPVOTE AFTER
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
each sold bar has a 36N/m weigh If the 1:In the following arrangement of structur allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. 36N/M 2m im Im 2m
Required information Link AB, of width b = 2 in. and thickness t= in., is used to support the end of a horizontal beam. The average normal stress in the link is -21 ksi and the average shearing stress in each of the two pins is 12 ksi. 4 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the diameter d of the pins. The diameter d of the pins is in.
6. JA line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the material of the shaft is 42 MPa. If the shaft carries a central load of 900 N and is simply supported between bearing 3 metre apart, determine the diameter of the shaft. The maximum tensile or compressive stress is not to exceed 56 MPa. [Ans. 50 mm] ort Fach nulley is 100
Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied? Use indenter diameter 10mm.
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
Group5/Two fork end pieces are to be joined together by a single steel pin of 25mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m². What will be the maximum shear stress in the pin?
PROBLEM 1: The timber beam loaded as shown has the cross section shown. If the working flexure stress islimited to 16 MPa, determine the cross sectional dimensions of the beam using a height to base ratioof 2. Ignore beam weight. Express your answer in mm.