Group5/Two fork end pieces are to be joined together by a single steel pin of 25mm diameterand they are required to transmit 50 kN. Determine the minimum cross-sectional area ofmaterial required in one branch of either fork if the stress in the fork material is not to exceed180 MN/m². What will be the maximum shear stress in the pin?

Given DataLoad to be transmitted (Force), F=50kN=50,000NDiameter of the steel pin,…

Answered: Group5/Two fork end pieces are to be…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.10P: Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa

See similar textbooks

Similar questions

The member consists of the steel rod AB that is screwed into the end of the bronze rod Find the largest value of P that meets the following design criteria: (a) the overall length of the member is not to change by more than 3 mm; and (b) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze.
Question 2
3. Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
Draw and label the free body diagram correctly.
Need solution tnx
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below. Pins at A, C, and D are smooth. Determine (a)The load P.(b)The minimum diameter for pin C if it is in single shear and the cross-shearing stress is limited to 70 MPa.(c)The minimum diameter for pin D if it is in double shear and the cross-shearing stress is limited to 70 MPa.
Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following:a. Calculate the tension of the cable.b. Determine the diameter of the wire if the allowable stress is 125 MPa.c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN. Determine the smallest allowable outside diameter of the tube if the working stress is 110 MN/m2 Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each plankes if the working bearing stress for wood is 13 MPa. 20 mm
1. A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use EsT=200GPA, EAL = 70 GPa, and EBr = 83 GPa. As = 480 mm? Ab=650 mm? Al= 320 mm? 2P 4P 3P 1m 2m 1.5m
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
Kindly show the complete step-by-step solution and free body diagram. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. I need the answer right away, thank you.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS