Q20 An engine using fuel of calorific value 42000 kj/kg has abrake thermalefficiency of 30%. Find its brake specific fuel consumption in gramAnswer [ 285.71 gm/kw_hr]9.1b-p-hr

1KW= = 1 kilo jule/secondm*cv (kg/second *KJ/kg = == = KJ/second = KW)

Answered: Q20 An engine using fuel of calorific…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

confused with answer 60% and 69% Please do it correctly or skip if you are unsure. [within 30minutes]
Engine Type: Single cylinder Four stroke Diesel engine, Bore: 0.0875m, Stroke: 0.11m Capacity: 661.5 cc, Power: 6 H.P. at 1500 rpm, Torque: 2.96 kg.m at 1500 rpm and Compression Ratio :17.5:1 Explain how to measure the :- Fuel consumption. Inclined manometer readings for air flow. RPM, power output etc. (iv) Study of various components of diesel engine. (ii)
1.2 A four cylinder, four stroke diesel engine has brake mean effective pressure of 6 bar at full load speed of 600 rpm and specific fuel consumption of 0.25 kg/kWh. The cylinder has bore of 20 cm and stroke length of 30 cm. The air fuel ratio is measured as 26 from the exhaust gas analysis. The ambient conditions are 1 bar, 27°C. Assuming the calorific value of fuel as 43 MJ/kg determine 1.2.1 the brake thermal efficiency, 1.2.2 the volumetric efficiency, 1.2.3 the brake power.
The following data were obtained during a test of six cylinder otto cycle engine. Speed 2000 rpm, bore 3.5 in stroke 3.75 in, specific fuel consumption base on brake hp.66 lbs. / bhp-hr, brake arm 1.05 ft. HHV of fuel 20000 Btu/lb, Brake Torque 133 ft-lb, friction torque 40 ft-lb room temperature 90 F. barometric pressure 14.7 psia Find:a.) BHP=b.) BMEP=c.) IMEP=d.) IHP=e.) BRAKE THERMAL EFFICIENCY=f.) INDICATED THERMAL EFFICIENCY=
1. Operate at higher initial pressure. P1=80 bar (saturated) P2=1bar. Determine Point 1 and 2 then Calculate the efficiency of cycle and engine using Mollier chart. Draw p-v and t-s diagram. Can you show step by steps solution using the formula given?
ler eniine of a light truck owned by a utility company has been converted to run on . A dry analysis of the engine exhaust gives the following volumetric percentages : CO,(4.90%) , COO.79%) , 05(2.45%) Calculate the equivalence ratio at which the engine is operating .
solve the following explaining the steps please
Combined Gas-Vapor Power Cycle. Thermodynamics Trying to find T7 using the following equation. Don't understand how to get Ta, Tb, cp,a or (dp/dt)sat. No need to solve for values, but if you can explain how to get them I will appreciate it.
Given: = refueling Powertran SOURCE EMISSIONS vehide eff eff gasoline 266g co₂/kwh- HEV 0.90 0.285 FLgrid 411ilg Co₂/kWh 41111gCo₂/kWh EV 0.85 0.80 Production 11x10% og CO₂ 13.7 x 10°g CO₂ A) Calculate the breakeven pont (in km driven) for a EV against on HEV in Florida of 0.1kWh/kM Use a drive cycle conversion 5) How efficient would the powertrain of the HEV in this example have to be to break even with an EV in Florida after 150,000 Miles of service (240,000) km Is it plausible to achieve the answer from pert b Consideans the HaXINERY theoretical efficiency of the Carnot cycle is 5020 and there are additional losses of the transMISSION :- 90% efficiency ? c A what do you conclude is the leading factor in why EVs are less emissive than ICE,
Please solve immediately ,I have less time. Answer must be correct to get thumb up.
AM Q1: Choose the right answer The means if a sample is compressed in one direction it tends to get thicker in the lateral direction poission's ratio Hooke's Law Ductility A pressure vessel can be treated as thin- =walled when the r/t 10 10 10 or greater One of the below cycles is not under this category of Gas power cycle Brayton cycle Dual cycle Rankine cycle ||| %9A 1₁. 4
Round off 4 decimal, Powerplant subject A dynamometer test was done for one hour at steady load on a 6 cylinder diesel engine. It was found to use 42 kg of fuel having Q h = 42,000 J/g. Cylinder is 22.8 cm x 27 cm, 4 cycle type. Speed, 550 rpm and dynamometer torque at 27000 kg cm. Determine the brake power (KW) and the brake thermal efficiency (%).

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q20 An engine using fuel of calorific value 42000 kj/kg has abrake thermal efficiency of 30%. Find its brake specific fuel consumption in gram Answer [ 285.71 gm/kw_hr] 9.1 b-p-hr