A square bar carries series of loads as shown. Compute the load (kN) and stress (MPa) in each segment of the bar. Determine whether the load or stresses are tension (T) or compression (C). All loads act along the central axis of the bar. 30 mm 30 mm 80 kN 40 kN 30 mm 110 kN Cross section of the bar

A square bar carries series of loads as shown. Compute the load (kN) and stress (MPa) in each segment of the bar. Determine whether the load or stresses are tension (T) or compression (C). All loads act along the central axis of the bar. 30 mm 30 mm 80 kN 40 kN 30 mm 110 kN Cross section of the bar

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
The prismatic bar has a circular cross section with 100-mm diameter. In a test to determine its elastic properties, the bar is subjected to 4.8-MN (meganewton) axial loads. In terms of the coordinate system shown, what are the six components of the state of stress at a point of the bar that is not near the ends where the forces are applied?
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the normal stress σn perpendicular to plane AB and the shear stress τn⁢t parallel to plane AB. Assume α= 30°.Calculate the normal force N perpendicular to the plane AB and the shear force V parallel to plane AB. Report both answers as positive numbers.Answers: N = kips, V = kips.
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef 1110 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. = Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). Given: • L1 L2 = = 100 mm = 1.7 m • . L3 = = 1.4 mm RIGID PLATE ALUMINUM FACE PLATE F FOAM L2 |← 41 +| |—–—– 63 L1 L3 F = 37 kN σα = σ f = |ɗ| = = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) MPa ? MPa mm ?
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
For the stresses given with the cube below: 1. Compute the center, radius (R), principal normal stresses (0₁ and 03), max shear stress (Tmax) and draw the Mohr's Circle. 2. Compute the normal and shear stresses when the cube is rotated 20° clockwise from the horizontal plane and draw them on the cube. 3. The yield point stress (σyp) is 6 kPa. Determine if the material will fail under stresses shown using Tresca's Hexagon. вкра акра 6 экра 8 кра экра 4кра
The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 165 mm from the centroid of the rivet group. Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa
The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and cross-sectional areas (2 sg.in.) The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the stress in the steel rod when the force W= 10 kips is applied. Use Es=29 x 10^6 psi and Ea=10 x 10^6 psi. Express your final answer in psi to the nearest whole number. Note: Do not include the unit in your answer. * 3 ft B A 5.5ft 1.5 ft →
Need only handwritten solution only (not typed one).
The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 344 mm from the centroid of the rivet group. Assume a = 165 mm Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa
Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each section is 0.50 inches. Give the answer in Ib/in?. Assume Point A is a fixed support and the block at A is rigid. Indicate if it is in tension or compression. 3.50 kip 1.75 kip 5.00 kip B 3.50 kip A 1.75 kip 18 in. 12 in.- 16 in: CAR = units %3D II