Determine the internal forces at point J for the structure shown, where member BD can only carry axial forces. Take the dimension a = 180 mm and theexternal load P = 350 N.**225 mm225 mmaxial force:Fjshear force:SFJ=bending moment:BMJ ==APNVCJB*135 mma mm120 mm(tolerance 1 N, magnitude only)(tolerance 1 N, magnitude only)D(tolerance 100 N*mm, magnitude only)

Answered: Image /qna-images/answer/42e8fa7d-18a2-4c16-9090-2066ad00b64f.jpg

Determine the internal forces at point J for the structure shown, where member BD can only carry axial forces. Take the dimension a = 180 mm and the external load P = 350 N. * 225 mm 225 mm A PNV axial force: F₁ = shear force: SFJ= bending moment: BMJ = * 135 mm B a mm 120 mm * (tolerance 1 N, magnitude only) (tolerance 1 N, magnitude only) D (tolerance 100 N*mm, magnitude only)

Determine the internal forces at point J for the structure shown, where member BD can only carry axial forces. Take the dimension a = 180 mm and the external load P = 350 N. * 225 mm 225 mm A PNV axial force: F₁ = shear force: SFJ= bending moment: BMJ = * 135 mm B a mm 120 mm * (tolerance 1 N, magnitude only) (tolerance 1 N, magnitude only) D (tolerance 100 N*mm, magnitude only)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the equivalent stiffness constant of the ff.
Find the load on each bar of the cage given below. Its dimensions are base 2a and height 3a. EB passes through the midpoint of the lattice. Angle of force F1= 700 with horizontal (choose an angle between 15o and 75o)
3. If P= 100KN, Compute the total deformation. 112 in 201 60 CM 90 cm 9p 4P 7P $=2ch $=6m 644ch E= 120 GPa E = 200 GPa = 100 GPO
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ¢ = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb , what is the maximum weight Wmax of the crate that the system can support? What is the angle 0 required for D equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) vec ? Wmax, 0 = lb, degrees
Values are m= 360mm n= 375mm q= 24mm r= 18mm P= 0.6kN
5. A steel bar has dimension of 5 cm x 2.5 cm x 1.5 mm respectively. It is subjected 3 mutually perpendicular loads of 250 kN (Tensile), 2.5 MN (tensile), 3.5 MN (compressive) acting along length, breadth & thickness directions respectively. Find the change in volume. Take E as 200GPA & Poisson's ratio 0.25. Also find the change in Length, breadth & thickness.
What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant force of the triangular distributed load in the figure below. 8ANm Select one: a. F = 6 KN; d = 1 m b. F= 6 KN; d= 6.5 m c. F= 12 KN; d= 6 m d. F= 24 KN; d= 6 m
What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant dorce of the triangular distributed load in the figure below.
A mechanism carries a constant load P applied to the seat as shown. For the angle 8, determine the following (a) the lengths LBE and LAB, in m (b) the angles a and p, in degrees Draw the complete FBD of (c)members AB, FG, EBH and GHI Calculate the forces, in Newtons, for the following (d) member FG (e) pin H (f) hydraulic cylinder AB Parameter P = 724 N 8= 34.5° Note: Figures CDFE and EFGH are parallelograms. E 100 175 bis is not y 400 LBE ou op os dadog on funt an 150, B a This is not property so do not in any way are your an 150 D E 175 B 200-- Dimensions in millimeters G PH P 150 This is not your property so do not use it in any way as if it were your
Find the force P which is applied on point B of the triangle ABC, as * :shown in the figure below P=? B T= 600 N 5 m C/60 D -2.5m- P=216.7N P=226.7N P=206.7N
A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape are shown in the second figure. Assume LAB = 8 ft. LBc=2 ft, LCD= 4 ft, LDE= 4 ft, Pc = 1850 lb, PE = 2160 lb, WAB = 830 lb/ft, b₁ = 10 in., b2= 2 in., b3 = 6 in., d₁ = 2 in., d₂= 11 in., d3 = 2 in. Consider the entire 18-ft length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. Answers: (a) σT = (b) a = WAB LAB i 545.779 706.391 B Pc LBC b₁ b3 C LCD -b₂ psi. psi. D ↓ d₁ LDE d₂ PE E
Please show each and every step while solving. Thanks!