Answered: The beam is supported by double-shear…

The beam is supported by double-shear pins at A, B, and C. The radius of all the pins are r = 8 mm. Hint: 1. Remember that rod BC is a 2-force member 0₁ d₁ B F₁ d2 F₂ Ö F₁ dz d₁ A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 30 kips, F₂ = 14 kips, F3 = 20 kips, and F4 = 39 kips, determine the absolute value of the axial load in rod (2). EVOVE F3 (2) (3) A O 24 kips O 18 kips O 21 kips 28 kips O 17 kips B F3 F4 C D
2. The steel pipe has a length of L=24 in. If it is fixed at section C and subjected to the horizontal 200-lb force acting on the handle of the pipe wrench at its end, determine the internal loadings at the section A. 10 in. 14 in 200 lb
4) The composite shaft consists of a solid brass segment (1) and a solid aluminum segment (2) that are connected at flange B and securely attached to rigid walls at A and C. Brass segment (1) has a diameter of 18 mm, a length of L₁ = 235 mm, and a shear modulus of 39 GPa. Aluminum segment (2) has a diameter of 24 mm, a length of L₂ = 165 mm, and a shear modulus of 28 GPa. If a concentrated torque of 270 Nm is applied to flange B, determine (a) the maximum shear stress magnitudes in segments (1) and (2). (b) the rotation angle of flange B relative to support A. N y A 235 mm (1) B 165 mm 270 N-m (2) C x
Provide the correct exponents and distances to make the singularity function given valid for the beam shown. V₁ = 8 kN, V2 = 7 kN, V3 = 200 mm, and V4 = 1100 mm. Determine the reaction forces at the supports. ATATV3 -V3- (mm) O The singularity functions are q = R₁(x)ª − v₁(x − P)ª − v₂(x − Q)¹ + R₂(x − R)ª V = R₁ – v₁(x – D)³ − v2(x − E)³ + R2(x – F)³ M = R₁x – v₁(x – G)ª − v₂(x − H)C + R₂(x − 1)C From the given singularity functions the exponents aro (1) (2)
4 m B 4m 8 0.4 m AB X-Section 0.2 mIO (a) Determine to that results in the gap (8) being closed. (b) If w=628 kN/m, determine the internal force in member BC? BC X-Section For the bar shown above, a uniformly distributed axial load wo (force per unit length) is applied between A and B. The diameter of the cross sections AB and BC are also indicated. The material properties of the bar are: E= 20 GPa and 0.3. If the gap 61 mm, then answer the following questions (you can take a 3.14):
Solve the problems below: 1. The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smaller pipe has an outer diameter of 20 mm and an inner diameter of 18 mm, whereas the larger pipe has an outer diameter of 25 mm and an inner diameter of 20 mm. If the pipe is tightly secured to the wall at C, determine the maximum shear stress developed in eah section of the pipe when the couple shown is applied to the handles of the wrench. B 75 N 150 mm 200 mm 75 N
Draw the shear and moment diagrams, then answer the questions. The distance x is measured from point A to the right. Assume w 355 lb/ft, a-3.4 ft, b=3.1 ft. Questions: Atx=1.8 ft, V- Atx=4.6 ft, V= B lb, M- lb, M= i lb-ft lb-ft
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31 kips, F₂ = 11 kips, F3 = 22 kips, and F4 = 36 kips, determine the absolute value of the axial load in rod (2). F A F₂ (1) F₂ B F3 C (3) D O 16 kips O 12 kips O 7 kips O 9 kips O 22 kips
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 31 kips, F2 = 13 kips, F3 = 24 kips, and F4 = 37 kips, determine the absolute value of the axial load in rod (2).
2 m C. What is the magnitude of the internal normal force acting on the member at point C if P- 200 N? N-m What is the magnitude of the internal shear force acting on the member at point Cif P-200 N? What is the magnitude of the internal moment acting on the member at point C if P=200 N?
Part A A FA. FD= -600 mm- P 50 mm VE ΑΣΦ 41 B vec - 600 mm 25 mm If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 200 kN is applied. The assembly is made of A36 steel. (Figure 1) Enter your answer, separated by a comma. -0.15 mm D ? kN
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 a. Determine how much the wire stretches when the horizontal force acts on the pole. 3 ft 30 D 2.5 kip 4 ft B b. Determine the change in the wire's radius c. At what angle is the principal stresses on pole BC? Use Mohr's Circle. d. What is the principal stress in pol BC? Use Mohr's Circle e. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. f. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) g. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. h. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)