The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and cross-sectional areas (2 sq.in.) The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the stress in the steel rod when the force W= 10 kips is applied. Use Es=29 × 10^6 psi and Ea=10 x 10^6 psi. Express your final answer in psi to the nearest whole number. Note: Do not include the unit in your answer. - 3 ft B A 5.5ft 1.5 ft →

The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and cross-sectional areas (2 sq.in.) The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the stress in the steel rod when the force W= 10 kips is applied. Use Es=29 × 10^6 psi and Ea=10 x 10^6 psi. Express your final answer in psi to the nearest whole number. Note: Do not include the unit in your answer. - 3 ft B A 5.5ft 1.5 ft →

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B. SOLVE FOR THE STRESS IN THE ROD IF ITS CROSS-SECTIONAL AREA 1S 2500mm^2. ROD 8=50⁰ A= 2500mm^2 1.5m 3m P=25KN
600 lb 600 lb An aluminum rod to be used in an aircraft control system is required to stretch 0.12 in. when a 600-1b tensile load is applied to it. If E = 10.2 × 10³ ksi and the allowable stress is 17 ksi, determine the smallest diameter that can be selected for the rod and the corresponding required length of the rod.
The 3/4-in.-diameter shaft is subjected to the loading shown. Determine the stress components at point A. Sketch the results on a volume element located at this point. The journal bearing at C can exert only force components Cyand Cz on the shaft, and the thrust bearing at D can exert force components Dx, Dy, and Dz on the shaft.
A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 kN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa.
Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Take P= 24 kN. 04 0.25 Determine the maximum value of the average normal stress in the links connecting points Cand E (Input the answer with the appropriate sign.) The maximum value of the average normal stress in the links connecting polnts Cand Eis MPa.
The solid 0.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 500 lb/ft. Two concentrated loads also act on the rod: P = 1900 lb and Q = 900 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in.
Calculate the stress perpendicular to the inclined plane AB. Report your answer as a positive number.Answer: σn= Enter your answer in accordance to the question statement ksi.
Calculate the stress parallel to the inclined plane AB. Report your answer as a positive number.Answer: τn⁢t= Enter your answer in accordance to the question statement ksi.
Similar problem already solved on bartleby. Take reference from there.
Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A,B,C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is ot allow = 150 MPa and the allowable bearing stress for the wood is ob allow = 28 MPa. Assume that the %3D hole in the washers has the same diameter as the bolt. 2 kN 3 kN 1.5 kN -2 m--1.5 m--1.5 m--1.5 m--1.5 m- 2 m bolt washer
The U-bar shown below has a circular cross section with a diameter of 1 in. For the loading shown, determine the maximum and minimum normal stresses on a cross section between A and B. 500 lb- A B 2₁ 4 in 500 lb
- Write the Gilven and what is being asked. .Write your complete solution. -Round off your answers into TWO decimal places -BOX your final answer and don't forget the units.