Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each having a radius of 45 mm. The cylinder is shown in the figure below. If the cylinder has a wall thickness of 2 Mm, determine the circumferential stress in the wall of the cylinder. Express your answer to three significant figures and include appropriate units.

Q: 2000 1 45001 3100 N

A: given; force in x-direction(Fx)=-2000N (compressive)force in y-direction(Fy)=-4500N…

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: QUESTION 2. The elbow-shaped structure is under the effect of four forces that are applied as shown…

A: Given: The inner diameter of elbow, d = 40 mm The outer diameter of elbow, D = 48 mm

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm…

A: stress is defined as the force per unit area.

Q: he forces applied to pulleys are given as shown below. Accordingly, show the stress state at point A…

A:

Q: Q2/ The rigid bar ABCD is supported by a pin at B and restrained by identical steel bars at C and D,…

A: Given data as per the question Increase in temperature =800 c E = 200 Gpa Area =250 mm2 considering…

Q: Since the suspended mass is m=1500 kg as shown below; Find the force (F) N and the stress N/mm2 in…

A:

Q: A 150 min x a mnm x 20 mm stecl plate is subjected a pull of 150 kN along its central axis as show…

A:

Q: 2. Consider the Flamant solution - a line load on the edge of a half space. The valid stress…

A: according to a given question

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall…

A:

Q: PROBLEM 2. The forces shown in the figure are applied to a plate connected to a pipe with an outer…

A:

Q: A plane element is subjected to stress as shown in below figure. Determine the radius of the mohr…

A:

Q: The stress at a certain point is as shown in the figure. If the maximum in-plane shear stress…

A:

Q: Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by…

A:

Q: Engineer firms in many situations must verify the reliability of existing purchased designs. Your…

A:

Q: A typical aluminum-allóy scuba diving tank is shown in thế ngure. The outside diameter óf the tank…

A: Solution:

Q: A spherical pressure vessel 4 ft. in diameter with a wall thickness of 0.25 in is subjected to an…

A:

Q: Find the normal stress value on the new x-axis obtained by rotating the element with the stress…

A: Write the given data with suitable variables. σx=100 MPaσy=60 MPaζxy=45 MPa

Q: |P2=20kN 0.5 m A P1=100kN 40 mm 40 mm 25mm 25mm

A: Area of cross-section,A=50*80A=4000 mm2Moment of inertia about normal axis,Ix=50*80312 Ix=2133333.33…

Q: The built-up shaft in figure consists of a pipe AB and a solid rod BC. The pipe has an inner…

A: Given : outer diameter of pipe AB, Do = 28 mm inner diameter of pipe AB, Di = 20 mm diameter of rod…

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A:

Q: 1. A loaded bicycle pedal crank is shown below. 18. 750 N (-7 direction) d A @ Top -y₁ B@ Top d = 15…

A:

Q: The tank shown in the figure shown is fabricated from a steel plate. a. Determine the maximum…

A:

Q: 2. From the system shown in the figure, obtain the forces and the average axial stress on each bar…

A:

Q: The inner radius of the pressurized cylindrical tank is 1.25 m and the wall thickness is 15 mm. It…

A: We are given the following data: The inner radius of the cylinder, r=1.25 m Wall thickness of the…

Q: ne shear stress in

A:

Q: piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º…

A:

Q: Determine the equivalent stress state of an element oriented 30° clockwise with respect to the…

A:

Q: The tank shown with elliptical cross-section is fabricated from 14 mm steel plate. Determine the…

A:

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A:

Q: The same circular plate, as in the previous questions, is considered. Assume a plate radius of…

A:

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.000 in. and a wall thickness of 0.125…

A: For solution refer below images.

Q: lamp=81kg, AB=5mm, BC=8mm

A:

Q: A bar of square cross-section is subjected to point loads of P1, P2, P3, and P4 as shown here.  Find…

A: The tensile load tends to elongate the component and the compressive load tends to compress the…

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5…

A:

Q: There is a rectangular plate 2 mm thick on which the forces shown in the figure act. Determine…

A:

Q: The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a…

A: (a) To find: The axial force F in the ring in terms of p, w and r; Calculation: Consider a FBD by…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.