A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown in the figure. If the vessel sustains an internal pressure of 450 kPa, determine the average shear stress in the glue and the state of stress (axial and hoop components of stress) in the wall of the vessel.

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: A circular plate with simply supported edges subjected to a uniform pressure of P=1,450 KPa, as…

A:

Q: 2000 1 45001 3100 N

A: given; force in x-direction(Fx)=-2000N (compressive)force in y-direction(Fy)=-4500N…

Q: respectively. The tank has an inner diameter of 4 m. The thickness of the cylindrical are made from…

A: A scalar quantity in when when an amount of force act on the object in a cross section area, that is…

Q: The point on the surface of the pressure vessel in Fig.a is subjected to the state of plane stress.…

A: Given data: The maximum principal stress acting on the point of the pressure vessel is σ1 =16 MPa…

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: A thin-walled cylinder tank is subjected to a tensile stress of 100 Mpa. What is the longitudinal…

A: The tensile stress on the thin-walled cylinder tank is σt=100 MPa.

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A:

Q: A spherical and cylindrical gas tank has the same inner radius of 1.5 m. Which of the  two tanks can…

A: Given   Diameter, d = 2 x 1.5 = 3 m            Stress = 15 MPa    Thickness, t = 20 mm Find   The…

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 10 psf. If the wall thickness…

A: Given : Diameter, d = 4 ft = 48 in Internal pressure, P = 10 psf = 0.06944 psi [ 1 psi = 144 psf]…

Q: The maximum shear stress (in MPa) in the

A: Given;  A cylindrical tank of;  Inner radius,r=7 mm  Thickness=50 mm  Gauge pressure= 2 MPa…

Q: 2. Consider the Flamant solution - a line load on the edge of a half space. The valid stress…

A: according to a given question

Q: A pressurized steel tank has inner radius r = 0.5 m and wall thickness t = 20 mm. The steel has…

A: Given data: Before proceeding with the solution check whether it is a thin or thick pressure…

Q: PROBLEM 2. The forces shown in the figure are applied to a plate connected to a pipe with an outer…

A:

Q: A solid 30-mm-diameter shaft is used in an aircraft engine to transmit 86 kW at 1,250 rpm to a…

A: The diameter of shaft is The power transmitted is .The speed is The thrust developed is

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A:

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

A:

Q: A typical aluminum-allóy scuba diving tank is shown in thế ngure. The outside diameter óf the tank…

A: Solution:

Q: A spherical pressure vessel 4 ft. in diameter with a wall thickness of 0.25 in is subjected to an…

A:

Q: The propane storage tank shown in Photo has an outer diameter of 3.3 m and a wall thickness of 18…

A: Hello. Since your question has multiple parts, we will solve first question for you. If you want…

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400…

A:

Q: Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress=30…

A: Given data : Maximum shear stress ζMax=80 MPa Minimum principal stress σ2=30 MPa   Required :…

Q: 3.5 m r= 0.6e-0.08y² y 0.6 m

A:

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and txy…

A: Given, Stress in x-direction = σx = 20 MPa Stress in y-direction = σy = 80 MPa Sheat stress in…

Q: In a cylindrical container, Gas is compressed to a pressure of 3 MPa. If the cylinder has a diameter…

A: Boiler shells, pressure tanks, pipes, and other low-pressure processing equipment all use…

Q: Calculate the tangential stress at a point on the plate that forms a cylindrical reservoir, known as…

A:

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 820 mm and a wall…

A:

Q: Current Attempt in Progress Consider a point in a structural member that is subjected to plane…

A:

Q: The stresses on an element are o, = -300 psi and o „=-600 psi. Find the maximum shear stresses on…

A:

Q: The 2-meter-high pressure tank below contains gas with internal pressure of 2 MPa. It is subjecte to…

A: Givenh=2mP=2MPaFex=15kNt=30mm=0.030m

Q: The inner radius of the pressurized cylindrical tank is 1.25 m and the wall thickness is 15 mm. It…

A: We are given the following data: The inner radius of the cylinder, r=1.25 m Wall thickness of the…

Q: The pressure tank shown is fabricated from 1/8-in steel plate. Calculate the allowable internal…

A:

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A:

Q: Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress=30…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.