o (MPa) 8. 32 MPa 16 16 MPa -16- (a) -32 т (MPa) (b)

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: 5. Determine the normal stress and shear stress acting on the inclined plane AB. Soive the problem…

A:

Q: Oy Txy

A: given; normal stress in x direction =σxnormal stress in y direction =σyshear stress in xy…

Q: The stress case at a point of a body is shown on the element below. Determine the principal normal…

A: The principal normal stresses, principal shear stresses, and the directions. Given: The stress in…

Q: At a point on the free surface of a stressed body, the normal stresses are 20 ksi (T) on a vertical…

A:

Q: The figure shows the stresses at a point. Determine the principal stresses and the maximum shear…

A:

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: Determine

A:

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

A:

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

A:

Q: The state of stress acting at a critical point on a machine element is shown. 1. Estimate the shear…

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each…

A: Force, P = 3 kN = 3000 N Radius, r = 45 mm = 0.045 m Wall Thickness, t = 2 mm = 0.002 m

Q: QU For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: re, determine the state A and at point B. Dra plume elements at A am results.

A:

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Given:- σx=70 MN/m2σy=50 MN/m2τxy=30MN/m2θ=30° To find:- The magnitude of the normal, tangential,…

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A:

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

A:

Q: A spherical pressure vessel 4 ft. in diameter with a wall thickness of 0.25 in is subjected to an…

A:

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: Determine the equivalent state of stress on an element at the same point which represents the…

A: According to the given dataWe need to findAverage normal stressMaximum in-plane shear…

Q: -80 MPa and T = 60 MPa The loading on the component is increased so that stresses are increased to…

A: GIVEN:maximum normal stress=300mpamaximum shear stress=200mpa

Q: A body is moving in a curved path with speed of 10 m/s and tangential acceleration of 3 m/s2. If…

A: Given, Speed of the car = v = 10 m/s Tangential acceleration = at = 3 m/s2 Radius of curvature = r =…

Q: Consider the stress element below. (a) Determine the three principle stresses and three shear…

A:

Q: Q2 / The 60° strain rosette are mounted on articular cartilage element. Figure Q2 shows the readings…

A: Consider the diagram shown below for the strain rosette. The general equation for the strain in a…

Q: 9-74 If the box wrench is subjected to the 50 lb force, determine the principal stresses and maximum…

A:

Q: The shaft has a diameter d and is subjected to the loadings shown. Determine the principal stresses…

A: Given: The load acting at the centre of the shaft is P.  The the axial force acting on the shaft is…

Q: Q1/ For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A:

Q: 2. Determine the state of stress at point H. Each section of the pipe has an inner and outer…

A: To find: The state of stress at point H. Given: The internal diameter of pipe is  di=36 mm. The…

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: he shaft is loaded with torque and force acting at location B and C. Given the diameter of 1 in.,…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.