The motor shown operates at constant speed and develops a torque of 100 lb-in during normaloperation. Attached to the motor shaft is a gear reducer of ratio 5:1, that is, the reducer outputshaft rotates in the same direction as the motor but at one-fifth motor speed. Rotation of thereducer housing is prevented by the "torque arm" pin-connected at each end as shown. Thereducer output shaft drives the load through a flexible coupling. Neglecting gravity and friction,what loads are applied to (a) the torque arm, (b) the motor output shaft, and (c) the reduceroutput shaft?MotorGear reducerFlexiblecoupling(Toload)Torque arm-Torque armReduceroutput shaftMotorReducerShaftrotation

Answered: The motor shown operates at constant…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

solve show all steps and solutions for a-e
Hello, could you please help. i need to work out the holding torque, thanks
3. Design a roller chain drive. Specify the chain size, the sizes and number of teeth in the sprockets, the number of chain pitches, and the center distance. Problem Driver Driven Input Input Power Nominal Туре Machine speed output (HP) (kW) speed(rpm) (rpm) 500 Roller 250 6-cylinder engine Heavy 40 29.8 Chain Conveyor
A motor with a power rating of 1800 Watts is coupled to the input shaft of the pinion (or driver), Gear A as shown in Figure c, the input shaft rotates at 650 revolutions per minute (rpm). Calculate the torque at the input shaft and at the output shaft. Assume no losses and 100% efficiency. Gear A: 22 TeethGear B: 48 TeethGear C: 30 TeethGear D: 70 Teeth
3. Figure 4 shows a simplified schematic of the drive system of joint 4 of the PUMA 560. The torsional stiffness of the couplings is 200 Nt-m/radian each, that of the shaft is 400 Nt-m/radian, and each of the reduction gear pairs has been measured to have output stiffness of 2000 Nt-m/radian with its input gears fixed. Both the first and second reductions have n=4. Assuming the structure and bearing are perfectly rigid, a) What is the effective stiffness of gear 1 if the electric motor's shaft is locked? b) What is the effective stiffness of gear 3 if the electric motor's shaft is locked? c) What is the stiffness of the joint (i.e., when the motor's shaft is locked)? In other words, find out the effective stiffness of the output gear 4. - Electric motor -#1 Coupling Connecting rod #2 Coupling -#1 Gear 42 Gear #3 Gear - #4 Gear Figure 4: Simplified version of the driven train of joint 4 of PUMA 560.
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
Could you please help,
Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the operating pressure angle is 20° The minimum value of addendum needed to ensure continuous transmission of motion is
1. The figure below is a spur gear train drive and gear 2 is the inlet of the gear train. It transfers 12 kw of power at 1200 rpm. Gear 3 and 4 have 60 and 20 teeth respectively and are made with 20° pressure and full-depth teeth. The desired speed for the output shaft is 32 rpm. a. Find the minimum number tooth on gear 2 to obtain 32 rpm at the output and confirm its validation for interference-free power transfer. b. Find the speed ratio at each gear set using the results obtained at "a"(above). c. Determine the rotational speed of each gear (n2, n3, n4, and ns) using the results obtained at "a"(above). d. Find the torque of each shaft (Tin, Te, Tout) assuming that there is no frictional loss during the power transfer. e. Determine the radial, tangential and total forces transmitted at the last gear set assuming a module as m=4 mm, and draw the free body diagram of gear 4 showing the forces and torques. 75 100 2007 In Out
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
Second question please

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS