1. A gas mass-flow rate expands into a fixed duct, from p₁ = 10 bar, T₁° = 380K down to the pressure p2 = 5 bar. A The total pressure in the outlet section is the same as the inlet one BThe total pressure in the outlet section is higher than the inlet one C□ The total pressure in the outlet section is lower than the inlet one Do More information is required to give the answer

1. A gas mass-flow rate expands into a fixed duct, from p₁ = 10 bar, T₁° = 380K down to the pressure p2 = 5 bar. A The total pressure in the outlet section is the same as the inlet one BThe total pressure in the outlet section is higher than the inlet one C□ The total pressure in the outlet section is lower than the inlet one Do More information is required to give the answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

55 kmol per hour of air is compressed from P1 = 1 bar to P2 = 6.1 bar in a steady flow compressor. Delivered mechanical power is 98.9 kW. Temperatures and velocities are: T1 = 301K T2 = 520 K, u1 = 10.8 m/s and u2 = 3.8 m/s. Estimate the rate of heat transfer from the compressor in kW, 3 decimal values. Assume that Cp = 7/2R and that enthalpy is independent of pressure.
Please solve and show all steps in solution or explain how to get numbers
pls correct the given. this is my last attempt thanks
A jet engine consists of a diffuser, compressor, combustor, turbine, and nozzle. Flow in the diffuser and nozzle are isentropic and flow through the compressor and turbine can be idealized as isentropic. Label the inlets to each component as: a, 1, 2, 3, and 4, respectively, and the nozzle exit as 5. The given parameters are as follows: air pressure and temperature at the diffuser inlet, Pa and Ta, respectively, the speed of air entering the diffuser, va, the compressor pressure ratio, r, the turbine inlet temperature, T3, and the air pressure at the nozzle exit, P5 = Pa. Assume that the working fluid is air alone and use an air standard analysis, i.e., take into account the temperature dependence of air specific heats. Note: the kinetic energies at the diffuser inlet and nozzle exit are comparable to the corresponding enthalpies. a) Find symbolically, in detail, air temperatures at all principal locations: a, 1, 2, 3, 4, and 5 (where some of these are given). b) Find symbolically, in…
Saturated steam at P1=25 bar expands adiabatically through a throttling valve to P2=4 bar. If the quality of the steam at the valve inlet is x1=0.9 what is the quality x2 at the valve outlet Please respond ASAP
Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.
FLUID MACHINERIES NEED ANSWER ASAP
Looking for velocity at the exit and mass flow rate. Show step by step solution please thank youu
Use the deal gas law to find the temperature rise/drop in the air (M = 18.57 kg/kmol) for the constant pressure from the atmospheric conditions (p = 100 kPa, T = 15 degrees Celsius) To v2 = 0.6 m^3/kg The universal gas constant is 7.123 kj/kmol K 0 degrees Celsius = 273.16 K
Q.- one kg of am ideal gas (R = 287 K irreversible Process from Stette-0 [1 bur, 300 k] to State - [2 bar, 300k]. The entropy change (S₂-S1) J kg-k
Carbon dioxide gas enters a water-cooled compressor at the initial conditions P₁ = 1.0 bar and T₂ = 284.15 K and is discharged at the final conditions P₂ = 35.8 bar and T, = 366.15 K. The entering CO₂ flows through a 100-mm diameter pipe with a velocity of 6 m/s and is discharged through a 25-mm diameter pipe. The shaft work supplied to the compressor is 12,500 kJ/mol. What is the heat transfer rate from the compressor in kW? H₁ = 714 kJ/kg H₂ = 768 kJ/kg V₁ = 0.5774 m³/kg V₂ = 0.0175 m³/kg
Q. - ome kg of an ideal gas (R = 287 J um irreversible Process from Stelte - 0 [1 bar, 300 k] to State - [2 bar, 300k]. The entropy change (S2-S1) J kg-k