Q2: The plate material of a pressure vessel is AISI 1050 QT 205 °C. The plate is rolled to adiameter of 1.2 m. The two sides of the plate are connected via a riveted joint as shown below. Ifthe rivet material is G10500 with HB=197 and all rivet sizes M31. Find the required rivet sizewhen the pressure vessel is subjected to an internal pressure of 500 MPa. Take safety factor = 2.1.2mAB'AChopeolm10.50.23hope

Step 1:For AISI 1050 STEEL taking the minimum thickness of the sheet metal is 22mm and we are…

Answered: Q2: The plate material of a pressure…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What’s the answer for this please ?
3.4 A storage tank is 5 m in diameter, 4 m high and the density of the fluid itcontains is 795 kg/m3. Determine the required wall thickness if the yieldstress of the material is 325 MPa, the factor of safety is 10 and the efficiency ofthe longitudinal joint is 80 %.
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - Blank 1 mm Inside diameter - Blank 2 mm Lenght - Blank 3 mm Note: All answer must be round off up to 3 decimal places.
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.
The opening between a 3m long piece of steel ...
A closed thin walled cylindrical vessel has a diameter D of 290 mm, a wall thickness t of 5 mm and length L of 210 mm. It is subject to an internal pressure P of 18 MPa causing circumferential stress and longitudinal stress in the vessel. Calculate the longitudinal stress due to the internal pressure. Give your answer in MPa to 3 significant figures. 00 P D 60 de OL
Find the thickness of a metal needed of the semi-spherical end of cylinder vessel 0.70 meter in diameter to an internal pressure of 2.70 N/mm2. The material is mild steel and tensile is 69 N/mm2
A thick cylinder has an outside diameter of 100 mm and an inside diameter of 60 mm. It is pressurized until internally until the outer layer has circumferential stress of 300 MPa. Calculate the pressure difference between the inside and outside. (Note: Please insert your answer with at least one decimal place. (the answer is in MegaPascal, MPa)
a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa
A steel panel is subjected to a compressive loading in order to improve the panel stiffness and to increase its buckling strength. It is swaged with the swage depth of 13 mm and swage angle of 60.07°. Its profile is as shown in Fig.Q2. Typical dimensions are shown in the figure and the thickness of the panel is 0.8 mm. The effective length of the panel is 750 mm. The relevant properties are: Modulus of elasticity Yield stress 200 GN/m? 240 MN/m? . Assuming that the buckling stress coefficient for a panel simply supported on both sides is 3.62 and that the post buckling relationship for the panel is Oy = 0.40, +0.60, where oav = average panel stress, o, = edge stress in panel and o = panel buckling stress, determine (a) the load/swage pitch at which initial buckling of the panel will ccur, (b) the instability load per swage pitch. (13 Discuss the effects upon the compressive strength of the panel of: (c) i) Varying the swage width; ii) Varying the swage depth 150 13 150 All dimensions…
The cover of a cylindrical pressure vessel made of cast iron is shown in fig.1 The inner diameter of the cylinder is 500 mm and the internal pressure is limited to 2MPa. The cover is fixed to the cylinder by means of 16 bolts with a nominal diameter of 20 mm. Each bolt is initially tightened with a preload of 20 KN. The bolts are made of steel FeE250 (S yt = 250 N/ mm 2 ). Assume. E for steel = 207 KN/mm 2 ,E for cast iron = 100 KN/mm 2, E for Zinc = 90 KN/mm 2,Determine the factor of safety for bolts considering the effect of the gasket.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS