The opening between a 3m long piece of steel and a rigid support is 1.5mm.As the temperature rises the opening begins to close. Find the temperature to fill the 1.5mm and also find the stress in the material when the temperature rises another 25 degrees. (coeff exp = 1.1 x 10³/C)

Q: Q1) Find the distance of resultant from point(a). 20N -3m 30N 4 30 15N

A:

Q: In performing his favorite workout routine, Jason throws a ball with an initial velocity of 12.3 m/s…

A:

Q: Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH= 1200N (C)…

A: Given AC=1000 N (Tensile)          EG= 520 N (Tensile)          FH =1200 N (Compression)

Q: 9-67. Determine the principal stress, the maximum in-plane shear stress, and average normal stress…

A: Given:σx=350 MPaσy=-200 MPaζxy=500 MPa

Q: Two boys riding in bicycles A and B respectively travels towards each other. When the distance…

A:

Q: Q2\ The 120-N force is applied as shown to one end of the curved wrench. If a=30 calculate the…

A: Determine the moment about point O  Mo=Fcosα(OB)+Fsinα(AB) ...(1)Mo=41.53768 NmFor moment about O to…

Q: Figure Q3 shows stainless steel shaft consists of solid 40 mm diameter section (1), 30 mm diameter…

A:

Q: For the truss and loading shown, determine the magnitude of the force (Ib) in member CE, if P =…

A:

Q: 4. Helium at 149 kPa absolute and 10°C is isentropically compressed to one-fourth of its original…

A: Answer 4: Given data: P1=149 kPaT1=10°CV2=14V1 Need to determine the final pressure.

Q: The reaction between fluorine and chlorine dioxide, F2(g) + CIO2(g) → 2FCIO2(g) Proceeds according…

A:

Q: A stone is thrown vertically upward from the ground with a velocity of 300ft/s. How long must one…

A:

Q: Q3: The uniform beam has a mass of 50 kg per meter of length. Determine the reaction the supports.…

A: GIVEN:

Q: Determine the tension in the cord and the acceleration of each block. Coefficient of friction…

A:

Q: The length of a pencil is measured with two rulers. Report the length of the pencil from cach ruler…

A: The length of the pencil is measured with two rulers :-

Q: i. A Wind Energy conversion system (WECS) with the following data is installed at a wind site.…

A:

Q: (F-Odd) When the motion of the particle is expressed as a = 6 · 2t, a is in m/s² . The particle is…

A:

Q: 3 The velocity of a particle which moves along the x axis is given by v = 2 – 4t + 5 tz, where t is…

A:

Q: Draw the F.B.D. for the beam shown in fig and then find the reactions at A * ? 2 kN 4 kN/m L--x A 3…

A: The given beam is a cantilever beam having a few loads on it. A is a fixed end. So, it will contain…

Q: The uniform 100-kg I-beam is supported initially by its end rollers on the horizontal surface at A…

A:

Q: Two blocks with masses m1 = 5 kg and m2 = 15 kg are connected by a rope as shown. The horizontal…

A: Answer: The speed of mass m2 after it has fallen by 6 m is 9.40 m/s2.

Q: Compare the heat loss from an insulated and an uninsulated copper pipe (k =400 W/m K) under the…

A: Given:Thermal conductivity of copper pipe, kc=400 W/m.KPipe internal diameter, d1=10 cm=0.10 mPipe…

Q: 04: Calculate the forces induced in members KL, CL, and CB by the 20-ton load on the cantilever…

A:

Q: 1. For the beam below determine bending moment 3' to the right from support A. 10K W-1k/ft 8K A R 3'…

A: drawing the free body diagram

Q: A plank 25 meters long is placed on rough inclined planes at an angle of 15 with the horizontal as…

A: For Find the value of x, 1). first apply force equilibrium eqn. along the plank and find relation…

Q: between centers carry pulleys 4 feet and 3 feet in diameter respectively, connected by a crossed…

A:

Q: A 30-g bullet is fired with a horizontal speed of 400 m/s at a 2-m long, 6-kg rod that is pinned at…

A:

Q: Water is flowing through point 1 (D = 22mm) and point 2 (d = 17mm) in the above venture meter. What…

A: According to the given data D1=222mm D2=17mm Q˙=0.70zl/s We need to find P1-P2

Q: Example 22.7I. A laminated steel spring, simply supported at the ends and centrally loaded, with a…

A: Springs are one of the flexible machine elements, which gets deformed when load is applied to it and…

Q: Calculate the magnitude of the force supported by the pin at A under the action of the 1.5-kN load…

A: Given data: The magnitude of force applied to the bracket, P = 1.5 kN. Draw a free-body diagram of…

Q: 4. Steam turbine with 80% stage efficiency receives steam at 7MPA and 550 deg C and exhausts as…

A: Find the quality after turbine expansion.

Q: Q3: You have a truss which is shown below, two forces applying on it in B and C joints, which are…

A:

Q: Q2: A force F with a magnitude of 100 N is applied at the origin O of the axes x-y-z as shown. The…

A:

Q: 6 KN Q3: Find the reactions for the following 3m 5 kN/m

A:

Q: Water at 60°F flows from a lake through 500 ft of 4- in ID cast iron pipe at a water turbine 250 ft…

A:

Q: 9-67. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

A:

Q: In Fig.B, Determine the magnitude of the resultant force acting on the screw eye and its direction…

A: Let F1=60N, F2=40N and F3=30N Angles made by different forces along X axis and Y axis are given in…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.