1. Two long rods of the same diameter-one made of brass (k=85w/m.k) andthe other made of copper (k=375 w/m.k) have one of their ends insertedinto a furnace (as shown in the following figure). Both rods are exposed tothe same environment. At a distance of 105 mm from the furnace, thetemperature of the brass rod is 120°C. At what distance from the furnacewill the same temperature be reached in the copper rod?Furnace105 mm T₁Brass rod⑪hToo-x2-TiCopper rod

The problem is about heat conduction in two different materials, brass and copper. The thermal…

Answered: 1. Two long rods of the same…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. If a 15 ft2 wall is to be constructed, how many bricks will be used? how many brick A and how many brick B?
O 4-Two identical metal plates (mass m, specific heat = 20°C, and the other is at 90 °C. They are placed in good thermal contact. What is their final temperature? c) have different temperatures; onc is
• An aluminum pot contains water that is kept steadily boiling (100 °C). The bottom surface of the pot, which is 12 mm thick and 1.5x10t mm2 in area, is maintained at a temperature of 102°C by an electric heating unit. Find the rate at which heat is transferred through the bottom surface. Compare this with a copper based pot. Tc 0 0 L=12mm Base of pot TH A= area of base
At a temperature of 21.4°C the hole in a steel plate has an area of 8.80 x 10- m2. You heat the plate until the area of the hole increases to 8.97 x 10- m2, which allows a steel rod to just slip through this hole. What is the final temperature of the plate? The coefficient of linear expansion of steel is 12 × 10-0/°C.
One side of a copper block 5 cm thick is maintained at 250 C. The other side is covered with a layer of fiberglass 2.5 em thick. The outside of the fiberglass is maintained at 35-C, and the total heat flow through the copper- fiberglass combination is 52 kW. What is the area of the slab?
You want to heat a house on a very cold day as shown in the figure. To do this, you want to use photovoltaic panels as an energy source. It would be about using 15 panels each with an area of 1.5 m2. These panels would be connected to an electrical resistance that would heat the house as shown in the figure. The house is losing heat through the walls and ceiling as shown in the figure. The panels are receiving solar radiation at a rate of 800 W / m2 and if their efficiency is 15%. How much will the temperature of the house rise after an hour? The house is hermetically sealed. Assume that the specific heats of air, cv and cp, are constant as shown in the figure. sol = sun fuga = leakage aire = air
Please show all calculations and type them out So that I will be able to read them and understand what you're saying I have bad eyesight and it is very difficult for me to read handwriting
3-28E A wall is constructed of two layers of 0.6-in-thick sheetrock (k = 0.10 Btu/h-ft-°F), which is a plasterboard made of two layers of heavy paper separated by a layer of gypsum, placed 7 in apart. The space between the sheetrocks is filled with fiberglass insulation (k = 0.020 Btu/h-ft F). Determine (a) the thermal resistance of the wall and (b) its R-value of insulation in English units. FIGURE P3-28E Fiberglass insulation Sheetrock 0.6 in 7 in I 0.6 in
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
3
A welding heat source is capable of transferring 160 kJ/min to the surface of a metal part. The heated area is approximately circular, and the heat intensity decreases with increasing radius as follows: 50% of the power is transferred within a circle of diameter = 0.25 cm and 75% is transferred within a concentric circle of diameter = 0.625 cm. What are the power densities in (a) the 0.25 cm diameter inner circle and (b) the 0.625 cm diameter ring that lies around the inner circle? (c) Are these power densities sufficient for melting metal?
A crucible of molten metal at 1800°C is placed on the foundry floor. The foundry man covers it with a metal sheet to reduce heat loss to the room. If the transfer factor, F, between the melt and the sheet is 0.4, and that between the top of the sheet and the room is 0.8, how much will the heat loss to the room be reduced by the sheet if the transfer factor between the uncovered melt and the room had been 0.8?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS