• An aluminum pot contains water that is kept steadily boiling (100 °C). The bottom surface of the pot, which is 12 mm thick and 1.5x10* mm2 in area, is maintained at a temperature of 102°C by an electric heating unit. Find the rate at which heat is transferred through the bottom surface. Compare this with a copper based pot. Tc 000 L=12mm Base of pot TH A= area of base

• An aluminum pot contains water that is kept steadily boiling (100 °C). The bottom surface of the pot, which is 12 mm thick and 1.5x10* mm2 in area, is maintained at a temperature of 102°C by an electric heating unit. Find the rate at which heat is transferred through the bottom surface. Compare this with a copper based pot. Tc 000 L=12mm Base of pot TH A= area of base

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Once upon a time, a student from a certain university wants to learn crystallization using a Swenson-Walker crystallizer. The capacity of this crystallizer is 0.6124 Ib/s of FeSO4 slurry leaves at 300 K. The flow mechanism of the cooling is counter current through the jacket and its temperature increases from 61 to 70 F. The overall heat transfer coefficient has been estimated to be 190 Sl units. (). Determine the requirement for cooling water in kg/hr (i) Let supposed that each crystallizer unit is 3.5 yard long and each metre of crystallizer provides26.91 ft? surface, how many crystallizer units will be required?
Handwrite please
Calculate its normal boiling point (in Kelvins). Write answer in THREE SIGNIFICANT FIGURES
Calculate the capillary effect in mm in a glass tube of 2mm diameter, when immersed in (1)water, (2)mercury. The temperature of the liquid is 25°C and the values of surface tensions of water and mercury at 25°C in contact with air is 0.0755 and 0.59N/m respectively. The angle of contact for water is 0° and 130° for mercury . Take the density of water 1000 kg/m3, specific gravity of mercury is 13.6. The capillary effect of water in mm is equal to= The capillary effect of mercury in mm is equal to=
9.5 m 9.5 m The two configurations above both have a wall thickness of 550 mm, and a length of 20 m. Which of the two configurations above should a company use if it plans on using a fire clay brick refractory with k = 1.74 W/m. °C? Explain your choice. 9.5 m
(cc) BY-NO-SA Niel Crews, 2013 An insulated, rigid vessel is initially empty (evacuated). However, it is connected to a steam line that is maintained at 200 psia and 500 °F. The valve is opened until the flow into the tank slows and stops (which occurs when the pressure in the tank is equal to the pressure in the steam line), at which point the valve is closed. What is the temperature within the vessel? °F
A copper rod, an aluminum rod, and a brass, each 6.00 m length and 1.00 cm diameter, are placed end to end with the aluminum rod between the other two. The free end of the copper rod is maintained at water’s boiling point, and the free end of the brass rod is maintained at water’s freezing point. If T1 and T2 are steady-state temperature copper-aluminum junction and aluminum-brass junction respectively. Where TC is temp at freezing point of water and TH is temp at boiling point of water. Show that the steady-state temperature for (a) the aluminum-brass junction is:
Pre-lab 8: Cold Engine The experimental setup for this week's lab consists of a syringe connected to a metal can (reservoir), a cold bath (water - ice mixture) and a "hot" bath (water at room temperature). A schematics of the syringe - reservoir system is shown below. Plunger of mass m Filled with gas (air) Syringe of volume Vcor VH - Volume Vo includes tube + Metal can -Metal can submerged in water of temperature Тс or TH. Tube Stopper Figure 1: Schematic of the syringe - reservoir system. The syringe is essentially a glass cylinder fitted with a movable piston (plunger). The markings on the syringe indicate the volume of gas in the syringe, but do not include the additional, unknown volume, Vo, in the gas can and tubing.
For what situations will the lumped capacitance method be valid if a solid is in contact with a fluid? Circle all appropriate answers. (a) The resistance to conduction within the solid is small compared to the resistance to convection due to a fluid. (b) The temperature gradient within the solid is large. (c) The Biot number is small (less than 0.1). (d) All of the above. (e) None of the above
Q1 An insulated ver tical cylinder Contains gas with as shown in the gure. The mass of the pston is 5ky cnd f intially, rest on the bettem et the cylnder The ylindder IS connecfed to nitrogen tank at' 01 kg et Argen the help ofa fictionless non- conducting pisten fgure Is Connected to nitegrn dank fitted with the valve. The value is opened and witregen slowly enters loo bar to a pipeling glinder During this perocrss, the piston is lifted pressure the to a heght e4 locm by Nitragen gas. the inidial cnd temperature of argen are 4 Agon as and r-167 Find the net workolone ky the Nitrogen Jook and 1 bav- The final tempemtve Is 520k, for gen gas R-0.208 Ky tg. k Angen lesulated gander tecm olm Valve Pisten Nitregen 1oo bar
Answer correctly and quickly as possible please. Please help me with my last three questions, I do not have any ask an expert left. Please.
I need the answer as soon as possible