۲/۱ : +0 العنوان seoni 4) 1 Mg (dry weight) of a non-porous solid is dried under constant drying conditions with an air velocity of 0.75 m/s parallel to the drying surface. The area of drying surface is 55 m2 If initial rate of drying is 0.3 g/m2 s, how long it will take to dry a material from 0.15 to 0.025 kg water/kg dry solid? The critical moisture content is 0.125 and the equilibrium moisture is negligible. The falling rate of drying is linear in moisture content. If air velocity increases to 4 m/s, what will be the anticipated saving in drying time? 0 osther

۲/۱ : +0 العنوان seoni 4) 1 Mg (dry weight) of a non-porous solid is dried under constant drying conditions with an air velocity of 0.75 m/s parallel to the drying surface. The area of drying surface is 55 m2 If initial rate of drying is 0.3 g/m2 s, how long it will take to dry a material from 0.15 to 0.025 kg water/kg dry solid? The critical moisture content is 0.125 and the equilibrium moisture is negligible. The falling rate of drying is linear in moisture content. If air velocity increases to 4 m/s, what will be the anticipated saving in drying time? 0 osther

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter11: Heat Transfer By Radiation

Section: Chapter Questions

Problem 11.3DP

See similar textbooks

Similar questions

Combustion of a fuel sampie in a bomb calorimeter increases the temperature of the entire system by 5.10 °C if the calorimeter contains 1500 g of water, but only by 4.00 "Cif the calorimeter contains 1950g of water. What is the heat capacity of the dry bomb calorimeter assembly? Assume that the specific heat capacity of water is 4.18 J A. 570 J "C- B. 912 J "C-1 C. 722 J "C- D. 366 J "C-1 E. 494 J "C-
Need neat and clean handwritten solution with step wise explaination and plagiarism free. Thanks.
Thermal properties of mould and Iron is given as latent heat of iron = 270 the freezing temperature of iron = 1500 C. the density of molten iron = 7500 kg kJ kg-K the specific heat of mould material = 1.2 the themal condudivity of mould material = 09 Wm-K the density of the mould material = 1500 kg Determine the solidification time for a slab-shaped casting of 16 e thickness when iỘn withaut superheat is poured into the sand mold at an initial m temperature of 300 C BI U
Show your commplete solution.
Please solve asap.
In a drying process, the moisture content of 35 kg of food will be reduced from 82% to 6%. The air used for drying enters the dryer at 80 ° C and exits at 70 ° C. To heat the air, 130 kg of saturated steam at 105 ° C is used. Food enters the dryer at 25 ° C and exits at 60 ° C. According to the ambient air temperature is 20 ° C; Calculate the drying efficiency based on evaporation latent heat and sensible heat. (Specific heat of food = 3.30 kJ / kg ° C)
-40 10 10² 103 Rupture time, h 10+ 10 Q1] B/ (16 Marks) To produce a lightweight epoxy part to provide thermal insulation. The available material are hollow glass beads for which the outside diameter is 1.6 mm and the wall thickness is 0.04 mm. Determine the weight and number of beads that must be added to the epoxy to produce a 0.5 kg of composite with a density of 0.65 g/cm³. The density of the glass is 2.5 g/cm³ and that of the epoxy is 1.25 g/cm³.
It is a problem of expansion and shrinkage of steel material so that the slightly smaller hole of a steel bushing of 1.999 diameter with the following process/materials/data to apply: Coefficient of expansion of carbon steel = 0.0000068 in/in-°F. Temperature raised by gas heating = 24.5 °F Cooling media to use dry ice with boiling point of -109.3 °F (-78.5 °C). Shrinkage rate below boiling point is 0.00073 in/in. Determine the final clearance between the expanded steel bushing hole against the shrinkage of the steel shaft. A. 0.000793 in B. 0.000693 in C. 0.000750 in D. 0.0008 in. Please solve elaborately and include the Units. Thank you dear, your solution will be appreciated much.
65 kg of foodstuff containing 73% water will be dried to 8% moisture content at 85 ° C. In the process of drying at atmospheric pressure, if the first temperature of the food is 23 ° C, calculate the heat energy (kj) required for the drying process (the heat capacity of the food is 3.2 kj / kg ° C and the heat capacity of the water is 4.186kj / kg ° C). A.)92536 B.)105432 C.)118328 D.)12896 E.)126942
Industrial pipes One of the ways to keep a pipe warm is by means of a steam tracer, through which an electrical resistance is used around the pipe and in a helical shape throughout its diameter?
The Occupational Safety and Health Administration has set a Permissible Exposure Limit of 1000 parts per million (ppm) of acetone. You are an industrial hygienist doing personal sampling on a worker who is supervising a production process that uses acetone. The upcoming exposures can be measured: 700 ppm for three hours and 1300 ppm for two hours. 3 hours at 900 ppm What is the TWA as calculated? What advice would you provide plant management regarding acetone exposure and PEL adherence?
Usng the phase chan For each thezgments below answer the assigned questions. Luestions will center around change in temperature, kinetic energy, particle speed, bonds breaking or forming. -Alo, make use of the following vocabulary words as they apply for each of the segments below GAS, SOLID, LIQUID, MEILTING, VAPORIZATION, FREEZING, CONDENSATION B-C 1. Wha process is taking place during this segment? 2. L chermal energy being added or removed during this segment? 1. Explain why the temperatture is not chaging during this segment. s the procE6s during this segment andothermic.or expthermic? C-D 5. What is thr sate of matterfor this segment? 6. What is happening to the temperature? 7. Explain why the temperatiure ischanging, 8. L this change an endothermic or exothumie process/ 9. Dexribe the kinetic energy during this sepment 10. Dexribe the particle speed during this gment.