5) Reaming is a process of enlarging a hole to obtain a precisehole diameter and good surface finish.a) Trueb) False6) Cutting Speed is expressed asa) Surface feet per secondb) RPMc) Inches per minuted) Surface feet per minute7) Reaming is a process ofa) Cutting threads in a Workpieceb) Making a precise hole in a Workpiecec) Making shape for a Socket flathead cap screw in aWorkpieced) Making shape for a Socket head cap screw in aWorkpiece.8) Tapping is a process ofa) Cutting threads in a Workpieceb) Making precise hole in a Workpiecec) Making shape for a Socket Flathead cap screw in aworkpieced) Making shape for a Socket head cap screw in aWorkpiece

Step 1: (5). The correct answer is: a) True Reaming is indeed a machining process used to slightly…

Answered: 5) Reaming is a process of enlarging a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need it in 15 minutes
Spinning at 10.0 revolutions per second (rev/s). The diameter of the electric drill bit is 4.00 mm. What is the linear speed of a point on the surface of the drill bit, in meters per second? Show computations a) 0.126 m/sec b) 0.105 m/sec c) 0.150 m/sec d) 0.160 m/sec
42) What are the names given to the three Taps used for Tapping Holes? a) Taper, Plug,Bottoming b) Taper, Fine, Course c) Fine,Course, Bottoming d) Top,Bottoming, Side 43) What does 16 represent for the Notation of 3/8-16UNC- 2A. a) Outside Diameter of a screw b) 16 Threads per Inch c) Fine Thread of the Screw d) Thread Tolerance 44) What does 3/8 represent for the Notation of 3/8-16 UNC- 2A a) Outside diameter of the Screw b) 16 Threads per Inch c) Fine Thread of the screw d) Thread Tolerance 45) Cutting Speed is ? a) The Peripheral distance travelled by The cutter b) The RPM of the Chuck c) The speed of the metal chips being cut d) The Feed Rate
10-12 Answer it correctly and this is Asap I will rate helpful if fast and perfect
29) For the shaft and hole sizes shown in the figure, specify the type of fit. 5.000 4.997 5.012 5.008 a) Shaft a) Clearance Fit b) Interference Fit c) Transition Fit 30) The location of a hole may be controlled by what GD&T symbol? b) c) d) Z Hole d) Clean Fit 31) Based on "ANSI/third angle projection", the Top view is normally above which view? a) Right Side b) Front c) Left Side d) Back Page 3 32) When you position a hole on a part which tolerance method gives you more acceptable parts a) Coordinate Tolerancing b) CMM Tolerancing c) Baseline Tolerancing d) Functional Tolerancing 33) The symbol indicates what term? a) diameter b) hole center c) zero d) radius 34) Which dimensioning scheme is best to minimize issues with tolerance? b) GD&T c) Coordinate Positioning a) Chain d) Baseline Copyright Univeristy of California
In drilling operations, the height of the generated hole constrained by: a) Cutting angle b) Shank length c) Body length d) Flute length e) Over all length
In section views, hatch pattems should be drawn parallel to one of the edges of the part. True! A) Yes, Almays B)Optional C)never
21) A Tap is driven with a) An adjustable Wrench b) A Combination Wrench c) A Tap Wrench d) Pliers 22) The alignment of a Tap could be checked with a a) Plumb Bob b) Square c) Level d) Dividers 23) The size of a Tap Drill is important because it a) Determines the size of a Thread b) Regulates the percentage of Thread c) Forms the Major Diameter d) Determines the depth of the hole 24) If the drilling speed is too high for the diameter of the drill and the Material being drilled, the result is a) A Rough hole b) Chips jammed in the Flutes c) The Margins or outer corners are broken down d) More feed is required to get the drill to cut and the drill can break
Solve it correctly please. I will rate accordingly with 4votes.
Tooth breakage on gear is usually a A) A crack B) None of These C) A contact Stress D) A Tensile fatigue
12- WHICH OF THE FOLLOWING ARE GIVEN AS THE CHIPS RATIO FORMULA R z = T. L a) = L. T R b) 2 = T R. L c) 190 d) z = T. R
This a not graded assignment, it is a question on a practice exam. Please do question 15

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS