What is the solution The spherical gas tank is fabricated bybolting together two hemispherical thinshells. If the 1 m inner radius tank, and 15mm of thickness, is to be designed towithstand a gauge pressure of 10 Mpa,determine the minimum number of 20 mmdiameter bolts that must be used to seal it.The bolts are made from a material havingallowable stress of 200 Mpa.

Answered: Image /qna-images/answer/baa21fbb-e454-4c69-845f-6b36507811e3.jpg

Answered: The spherical gas tank is fabricated by…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. If the tank is designed to withstand a pressure of 3 MPa, determine the required minimum thickness of the cylinder and hemispherical shells and the minimum required number of bolts for each hemispherical cap. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m.
A scuba tank has a cylindrical body and a spherical end-cap each of 7.5 inches in outer diameter. The wall thickness of the tank is 0.5 inches. The tank is made of aluminum alloy which has an ultimate tensile strength of 56 ksi. Determne the factor of safety against the bursting when the tank is pressurized to 3000 psi. Draw the FBD.
The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. If the tank wall has a thickness of 50 mm for cylindrical and hemispherical shells, The bolts were installed as 40 bolts/meter. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. What is the maximum pressure that tank can contain.
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 8.9 mm. For a gage pressure of 1.27 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume = 51. s Answers: (a) Normal stress= (b) Shear stress - MPa MPa
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 МРа, and the circumferential stress is limited to 60 МРа. A spherical shell with 70-in. outer diameter and 67-in. inner diameter contains helium at a pressure of 1200 psi. Compute the stress in the shell.
Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than 2km. The pipes are typically made from high grade steel plate (X80), which is bent, then seam welded to produce a section of pipe. During installation, sections of this pipe are welded together. In deep water, installation is usually conducted using the J-lay system. In the J-lay system, a string of pipe is hung from a barge, and allowed to fall to the sea floor, forming a J-shaped string. As the pipe is lowered, new sections are welded to the end of the string, and the barge moves forward. This system enables a good degree of accuracy in placing the pipe, and requires a less powerful ship than other laying systems. It does, however, place significant loads upon the pipe itself. 2000m Tmin=400m Pipeline m
The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the seams at an orientation of Assume B = 62.5. The tank has an inside diameter of d- 1800 mm and a wall thickness of t-7 mm. For a gage pressure of p-0.8 MPa, determine (a) the normal stress perpendicular to the weld and (b) the shear stress parallel to the weld. (a) on MPa (b) Tnt" MPa
Determine the minimum required number of longitudinal bolts per meter length at each side of the cylindrical shell. Express your answer as an integer. ΕΠΙ ΑΣΦ Η vec ne 184 = Submit Previous Answers Request Answer × Incorrect; Try Again; 3 attempts remaining
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness 30 mm. The gas contained in the tank is under a gauge pressure of 2.5 MPa. If the tank has an inner diameter of 8 m and is sealed with 900 bolts each 20 mm in diameter, determine the stress developed in each bolt.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
The storage capacity of a thin cylindrical pressure vessel is 0.028 m³. The cylinder is subjected to an internal pressure of 21 MPa. The length of the cylinder is twice its internal diameter. Determine all the dimensions of the cylinder, if (a) the longitudinal stress does not exceed 160 MPa; and (b) the circumferential stress does not exceed 235 Mpa.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS