scuba tank has a cylindrical body and a spherical end-cap each of 7.5 inches in  outer diameter. The wall thickness of the tank is 0.5 inches. The tank is made of aluminum alloy which has an ultimate tensile strength of 56 ksi. Determne the factor of  safety against the bursting when the tank is pressurized to 3000 psi. Draw the FBD.

Q: respectively. The tank has an inner diameter of 4 m. The thickness of the cylindrical are made from…

A: A scalar quantity in when when an amount of force act on the object in a cross section area, that is…

Q: pipe is hung from a barge, is lowered, new sections a stem enables a good degre- an other laving…

A: height of the pipe, h = 2000 mrmin = 400 mdiameter of the pie, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: 1 Eaxial Ehoop 91 92

A:

Q: A spherical shell with Do = inches and Di = inches contains a certain gas at a pressure of 1200 psi.…

A:

Q: Problem 4-73: The pipe is made of A992 steel and is connected to the collars at A and B. When the…

A: To findDetermine the average normal stress in the pipe.GivenPipe material A992 SteelTemperature…

Q: A lO-kN car and 5-kN hoist are supported 1.8 m above the floor by a cylinder with a 300-mm bore .…

A: Total force acting on the cylinder,F=10+5=15kN=15000N Area of the bore of the cylinder,A=π/4*(d^2)…

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: Height of the pipe, h = 2000 mrmin = 400 mDiameter of the pipe, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: A cylindrical tank is constructed with hemispherical heads. The tank diameter is 1.32 m, the wall…

A: Givend=1.32mt=20mm=0.02mP=1.560kPa

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 10 psf. If the wall thickness…

A: Given : Diameter, d = 4 ft = 48 in Internal pressure, P = 10 psf = 0.06944 psi [ 1 psi = 144 psf]…

Q: A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight…

A: Given: The diameter of tank, d = 50 in The weight density, ρg = 64 lb/ft^3 The depth, h = 9750 ft…

Q: Question 12 A 7-ft diameter spherical tank is subjected to an internal pressure of 45 psf. If the…

A:

Q: A piece of rubber block is placed in an open rectangular box made out of metal as shown in the…

A:

Q: Answer fully

A:

Q: Q1) Find the force F on the bottom of the tank if: K=1.5 m, H= 6 m, D=5 m. Air Oil Mercury s.g=0.9

A: Given data: k = 1.5 m H = 6 m D = 5 m S.G = 0.9 Need to determine the force at the bottom tank.

Q: The wall thickness of a 4-ft diameter spherical tank is 5/16- in. Calculate the allowable internal…

A:

Q: 1500 ft 3000 ft A 10 ppg mud weight is used after setting the surface casing. The surface casing is…

A:

Q: A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE…

A:

Q: A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m. Compute…

A: Given: The thickness of plate, t = 10 mm The internal diameter, d = 1.2 m The internal pressure, P =…

Q: Q2/ Compute the burst-pressure rating for 10.75-in., J-55 casing having a nominal wall thickness of…

A: The burst pressure rating is 3581.4 psi.

Q: Find the height of water column corresponding to a height of 19.5 КРа

A: Given data : Density of water=ρWAcceleration due to gravity=gPressure=PTo find :Height of water…

Q: The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft.…

A:

Q: A piece of rubber block is placed in an open rectangular box made out of metal as shown in the…

A: Please find the answer below

Q: As shown in the figure below, oil is inside the hydraulic press with SG=0.82. What force F is…

A:

Q: A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE…

A:

Q: the text sais the folowing two champers are closed but the chamber inn the middle has a piston is…

A: Mass of piston, m= 5kgDensity of oil, ρoil=720 kg/m3Density of water, ρwater=1000 kg/m3

Q: A thin spherical pressure vessel is required to contain 18 m3 of water at a gauge pressure of 700…

A:

Q: The two pistons at the ends of the cylinder gradually increase the air pressure. The circumferential…

A:

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 12 psf. If the wall thickness…

A:

Q: Question 5. A 3 m long metal cylinder with an external diameter of 600 mm and a wall thickness of 10…

A:

Q: For the dam shown, determine the factor of safety against sliding and overturning. Use unit weight…

A:

Q: water pressure is generated in this unconfined compression specimen at the failure?

A:

Q: a cylindrical pressure vesssel( diameter =2.8m and wall thickness of 35mm) is made of steel. the…

A:

Q: The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two…

A:

Q: The piston rod of an air operated press is to exert a maximum force of 20 kN. During the application…

A:

Q: Design a cylindrical pressure vessel to carry compressed air for a self-contaihed breathing…

A: given; →inside diameter(di)=20cm=200mm→outside diameter(do)=?→service pressure(P)=4MPa→design…

Q: In a triaxial compression test, for drained condition the confining pressure is 200 kPaand deviator…

A: Triaxial compression test, Calculate the net shear stress at the initial condition.

Q: What is the weight of the concrete to be placed on elbow of a pipe with a diameter of 800 mm knowing…

A: Given: Diameter of pipe, d=800 mm L=2000 m angle of elbow, θ=45° P=6 bar

Q: You have the thin walled pressure vessel shown. Given

A: Given that ,  Inner radius Ri=3.00ftWall thickness t=0.25in =0.020833 ft Length L=10 ft

Q: The pressure relieve valve has a spool of 1.5 sq inches area, if a pressure of 150 psi is required…

A:

Q: nd hemispherical shells, The bol and the 25 mm diameter bo able normal stress of 150 M

A: given data  tank thickness = 50 mm no of bolt/ length = 40  dia of bolt =25 mm allowable stress for…