A steel pipe 1.5m in diameter is required to carry an internal pressure of 750kPa. If the allowable tensile stress of steel is 140 MPa, determine the required thickness of the pipe in mm

Q: pipe is hung from a barge, is lowered, new sections a stem enables a good degre- an other laving…

A: height of the pipe, h = 2000 mrmin = 400 mdiameter of the pie, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: 1 Eaxial Ehoop 91 92

A:

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: Height of the pipe, h = 2000 mrmin = 400 mDiameter of the pipe, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: 2. A spherical stainless-steel tank having an inner diameter 'D', is used to store natural gas at a…

A:

Q: To build a Tesla car, a machine incorporated with a special tube having a 4mm wall, as shown below,…

A: Given: To find: Average shear stress at A and B

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 10 psf. If the wall thickness…

A: Given : Diameter, d = 4 ft = 48 in Internal pressure, P = 10 psf = 0.06944 psi [ 1 psi = 144 psf]…

Q: Calculate the tangential stress in the steel.

A: Given that ,  R=250mm  t=20mmP=4.5MN/m2  =4.5×106N/m2

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A:

Q: Question 12 A 7-ft diameter spherical tank is subjected to an internal pressure of 45 psf. If the…

A:

Q: A hemispherical pressure vessel with a diameter of 2 m and a wall thickness of 30 mm is filled with…

A: Givend=2m=2000mmt=30mmP=15MPa

Q: A cylindrical pressure vessel has an inner radius of 24 in. and wall thickness of 0.25 in. The yield…

A:

Q: the stresses at point A.

A: To find Stresses at point A

Q: Q2/ Find the diameter of steel rope required to lifting a machine of 3.25 tones weight safely, if…

A:

Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…

A: Given     Outside diameter, d2 = 0.8 in        Inside diameter, d2 = 0.19 in…

Q: A cylindrical tank holding oxygen at 3,470 kPa pressure has an outside diameter of 425 mm and a wall…

A:

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. (Figure 1) Figure…

A: According to the given datad=12 int=0.25 inP=280 psiWe need to findLongitudinal and hoop stress when…

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable…

A:

Q: A spherical stainless-steel tank having an inner diameter ‘D’, is used to store natural gas at a…

A: given data D = 620 mm    P =25 MPa    Tensile stress =1000 MPa  Shear stress = 440 MPa  modulus of…

Q: A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is…

A:

Q: material is 280 MPa. Using a safety factor of 1.5, determine the material thickness of the tank in…

A:

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: Introduction: The tension is created by fighting the bursting effect of the imposed internal…

Q: A spherical pressure vessel 4 ft. in diameter with a wall thickness of 0.25 in is subjected to an…

A:

Q: The thin-walled pipe has an inner diameter of 4 in. and a wall thickness of 0.1 in. If it is…

A:

Q: Q1/ For the assembly below, determine the average normal stress for the cable. Assume that the cable…

A:

Q: 2m Z 1.5 kPa R T I'm

A:

Q: The two pistons at the ends of the cylinder gradually increase the air pressure. The circumferential…

A:

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 12 psf. If the wall thickness…

A:

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 34 psf. If the wall thickness…

A:

Q: m high and 5 m in diameter is to be filled with water. Find the minimum thickness of the tank…

A:

Q: View Policies Current Attempt in Progress A typical stainless steel cylindrical vessel is shown. The…

A: Given data D = 48 in t = 0.75 in P = 1.1 ksi Find Hoop stress = ?

Q: The inner radius of the pressurized cylindrical tank is 1.25 m and the wall thickness is 15 mm. It…

A: We are given the following data: The inner radius of the cylinder, r=1.25 m Wall thickness of the…

Q: 6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 1D…

A: force, F=σ×AF=3.5×π4×4302F=508270.42 NP=F

Q: A basketball has a 300-mm outer diameter and a 3-mm wall thickness. Determine the normal stress in…

A: Outer diameter, D = 300 mm  Wall thickness, t = 3 mm  Inner diameter, d = D - 2t = 300 - (2*3)  d =…

Q: Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10…

A: Given  Pressure = 10 MPa Thickness of vessel = 38mm Hoops stress = 83MPa Pd/2t = 83 10d/(2×38)=83…

Q: 7) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 40 mm. The…

A: Given Data: Diameter of cylinder, d=550 mm Thickness, t=40 mm

Q: Applied mechanics: An undersea research vehicle has a spherical hull of 1m radius and a 40mm…

A: Radius r = 1m Thickness = 40mm High strength alloy steel  yield point =700MPa Relative density of…

Q: Q1/ Find the diameter of steel rope made from a ductile steel having a maximum stress 1500Kg/cm^2,…

A:

Q: The closed thin-walled tank has an inner radius of r and wall thickness t and contains a gas of…

A:

Q: holding oxygen at 2,058 kPa pressure has an outside

A: t/D= 13/393 Since value is less then 1/2/ So it is a thin cylinder

Q: 2 m 1.5 kPa

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.