6. Determine the percentage increase in heat transfer associated with attaching aluminum fins of rectangular profile to a plane wall. The fins are 50 mm long, 0.5 mm thick, and are equally spaced at a distance of 4 mm (250 fins/m). The convection coefficient associated with the bare wall is 40 W/m²-K, while that resulting from attachment of the fins is 30 W/m²K. Answer: 1315%

6. Determine the percentage increase in heat transfer associated with attaching aluminum fins of rectangular profile to a plane wall. The fins are 50 mm long, 0.5 mm thick, and are equally spaced at a distance of 4 mm (250 fins/m). The convection coefficient associated with the bare wall is 40 W/m²-K, while that resulting from attachment of the fins is 30 W/m²K. Answer: 1315%

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.38P: 2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from...

See similar textbooks

Similar questions

An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
What is the fin effectiveness of a rectangular plate fin made of aluminum O.3 mm thick mounted on a 16-mm-OD tube if the vertical tube spacing is 50 mm and the horizontal spacing is 40 mm? The air-side heat-transfer coefficient is 65 W/m2 • K, and the conductivity of aluminum is 202 W/m • K. Ans. ƞ is 0. 72 Please provide a comprehensive step by step solution on how to get the answer.
***answer is correct
A plane wall (0.8 m x 0.6 m) at 10 oC is to be heated by attaching 7-cm-long, 3-mm-diameter pin fins (k=200 W/mK, ρ=5000 kg/m3 ) to it. nfin=2000 fins are to be used in total. Temperature of the surrounding fluid is 100 oC, and the heat transfer coefficient on the surfaces is 35 W/m2K. Total (material + manufacturing) cost of the fins is 850 TL/kg. neglecting heat transfer from the fin tips a. nfin=? b.Fin effectiveness= c.Overall fin effectiveness= d.Total cost of fins (TL)=
One vessel having a carbon-steel wall of thickness 5 mm carrying saturated steam and water at 423K. The vessel is insulated with magnesia of thickness 50 mm. If the ambient air temperature is 321 K, determine the heat loss from the vessel. Given: i. thermal conductivity of carbon steel is 52 W/m.K ii. thermal conductivity of magnesia is 0.5 W/m.K iii. surface coefficient of insulation surface is 3 W/m2.K
Explain and write legibly
***answer is correct
A plane wall (0.8 m x 0.6 m) at 10 oC is to be heated by attaching 7-cm-long, 3-mm-diameter pin fins (k=200 W/mK, ρ=5000 kg/m3) to it. nfin=200 fins are to be used in total. Temperature of the surrounding fluid is 100 oC, and the heat transfer coefficient on the surfaces is 35 W/m2K. Total (material + manufacturing) cost of the fins is 850 TL/kg. Fill the table below by neglecting heat transfer from the fin tips. nfin=? a) Fin efficiency b) Fin effectiveness c) Overall fin effectiveness d) Total cost of fins
A total of 10 rectangular aluminum fins (k = 203 W/m-K) are placed on the outside flat surface of an electronic device. Each fin is 100 mm wide, 20 mm high and 4 mm thick. The fins are located parallel to each other at a center-to center distance of 8 mm. The temperature at the outside surface of the electronic device is 60°C. The air is at 20°C, and the heat transfer coefficient is 100 W/m? ‘K. Determine (a) the rate of heat loss from the electronic device to the surrounding air and (b) the fin effectiveness.
The outer surface of an oil heater at a uniform temperature of 100°C is to be filled with straight rectangular fins having a uniform thermal conductivity of 180 W/m.K. The ambient air temperature is 25°C and the heat transfer coefficient is 100 W/m².K. The fin thickness t-1mm, width w= 1m and its length is L= 10mm. If the heat transfer from the tip of the fin by convection, calculate fin efficiency and effectiveness. Tь =100 с Too = 25°C h = 100 W/m2-K L = 10 mm Air k= 180 W/m-K t = 1 mm
An aluminum fins 1.5 cm wide and 1 mm thick are placed on a 2.5 cm diameter tube to dissipate the heat . The tube surface temperature is 170 oC . Calculate the heat loss per fin for h= 130 W/m2 .oC for aluminum.
One side of refrigerated cold chamber is 6 m long by 3.7 m high and consists of 168 mm thickness of cork between outer and inner walls of wood. The outer wood wall is 30 mm thick and its outside face temperature is 20 deg C, the inner wood wall is 35 mm thick and its inside face temperature is -3 deg C. Taking the coefficient of thermal conductivity of cork and wood as 0.042 and 0.20 W/m-K respectively, calculate the heat transfer per second per sq meter of surface area. Select the correct response: 6.318 J 3.318 J 5.318 J 4.318 J