An off-axis lamina (0=22.5°) is show below. Calculate the off-axis shear strength Fs using the maximum stress theory. Consider both directions of shear, i.e., calculate both Fst and Fs. Are they equal? Explain your answer briefly. Use the properties for AS4/3501-6, a carbon epoxy material from Appendix A, table A-4, page 377) Positive shear Negative shear УЛ Is Is 0=22.5° 0 22.5° X X Is

An off-axis lamina (0=22.5°) is show below. Calculate the off-axis shear strength Fs using the maximum stress theory. Consider both directions of shear, i.e., calculate both Fst and Fs. Are they equal? Explain your answer briefly. Use the properties for AS4/3501-6, a carbon epoxy material from Appendix A, table A-4, page 377) Positive shear Negative shear УЛ Is Is 0=22.5° 0 22.5° X X Is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Similar questions

A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing maching until the applied torque reaches the value T = 500 N ·. At this value of torque, a strain gage oriented at 45º to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material?
A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
a) The total strain energy for a bar of length L. is given by the equation 2EA How would the equation change if the bar is tapered as shown in Figure Q4 (a)? Cakulation is not required. Figure Q4 (a) b) The frame ABCD with uniform diameter 40 mm and length L- 500 mm shown in Figure Q4 (b) is in the horizontal (xy) plane. One end of the frame (4) is fixed to a rigid wall and the other end (D) is subjected to a vertical force F-2 kN. Given that the frame is made of a material with E-80 GPa and G-30 GPa. Determine: i) The strain energy stored in the frame member CB (ignore energy due to shear). i) The vertical deflection at point D using Castigliano's second theorem (consider bending effecet only). Figure Q4 (b)
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
MD 1
28. (II) The bolts on the cylinder head of an engine require tightening to a torque of 95 m · N. If a wrench is 28 cm long, what force perpendicular to the wrench must the mechanic exert at its end? If the six-sided bolt head is 15 mm across (Fig. 8-44), estimate the force applied near each of the six points by a wrench. - 28 cm 15 mm on wrench Fon bolt FIGURE 8–44 Problem 28.
Please answer the question with the steps... Thank you
A brittle material made of ASTM grade 30 cast iron has ultimate strength in tension of 31 kpsi and ultimate strength in compression of 109 kpsi and undergoes the following plane of stress state: o, = 20 kpsi and Tyy = 10 kpsi (CW). a) using the 3D Mohr's circle, find all three principal normal stresses. b) using the Brittle-Coulomb-Mohr theory and Modified-Mohr theory, find the factors of safety for the given plane of stress state.