1. Steam at h=1300 BTU/lbm enters a boiler where 760 BTU/lbm ofheat is added. If 5 BTU/lbm are lost to the surroundings, whatis the final enthalpy of the steam?Do not usechatgpt, Onlyhandwritten

Given Information:The initial enthalpy (h1) = 1300 BTU per pound mass (BTU/lbm)Heat added in the…

Answered: 1. Steam at h=1300 BTU/lbm enters a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A water-tube boiler having a heating surface of 325.23 m² evaporates 6349.21 kg of water in an hour from a feed temperature of 66 °C. Boiler pressure is at 1.04 MPaa and the steam quality at the boiler outlet is 99 %. What percent of its rated Bo. Hp was the boiler developing?
An ammonia refrigeration compressor takes its suction from the evaporator, at a temperature of-200F and a quality of 95%. The compressor discharges at a pressure of 100 psi, liquid ammonia leaves the condenser at 500F.(a)Determine the heat absorbed by the evaporator in kJ/kg. (b)Determine the heat rejected to the condenser in kJ/kg. (c)Determine the COP. (d)Determine the horsepower per ton of refrigeration. (e)Determine the quality of refrigerant upon entering to the evaporator
Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.
please solve this
state all the formulae associated with adiabatic process
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
Saturated steam at 40∘C is to be cooled to saturated liquid in a condenser. The mass flow rate of the steam is 17.3 kg/s . Assume no pressure loss. a)Determine the rate of heat transfer. Q = ? MW
This is the only Superheated R-134a property table we are given, how do we find the final state of R-134a the superheated state from here? Thank you
A reheat cycle with two stages of reheating is executed with steam expanding initially from 25 MPa and 600 °C. The two reheater pressures are 4 MPa and 1 MPa, and the steam leaves each reheater at 600 °C. Condensation occurs at 40°C. What is hi in kJ/kg?
Air is cooled and dehumidified at constant pressure as shown in the figure below. Heat removed by the cooling coil is 130kW. Find air mass flow rate, air volumetric flow rate, condensation flow rate and sketch al states in a psychrometric diagram . Use AirH20 as the working fluid PLEASE NOTE: T2 has a typo, it should be 16.7 degrees Centigrade, not 16.7 degrees Fahrenheit, and all temperatures should be in Centigrade
I do not understand how to fix state 3 with the given information. Without knowledge of state 3 or 4s (the 4th state if the process were actually isentropic) I don't see how it's possible to get temperature or enthalpy of state 3.
TH 3 kg of air as an ideal gas undergoes a Carnot refrigeration cycle as shown The isothermal expansion occurs at 300K and isothermal compression occurs at 600K. The heat transfer to air during isothermal expansion is 125 kJ. Pressure at the end of figure. isothermal expansion is 75 kPa. a. Find pressure at the beginning of the isothermal expansion. Show all work and explain your numbers. b. Sketch this cycle on the T-s diagram. Show on the diagram the system states (1,2,3, and 4), the cycle direction, and the cycle work (not its amount)

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

1. Steam at h=1300 BTU/lbm enters a boiler where 760 BTU/lbm of heat is added. If 5 BTU/lbm are lost to the surroundings, what is the final enthalpy of the steam? Do not use chatgpt, Only handwritten