A cold storage room has a walls constructed of 0.102-m corkboard contained between double wooden walls each 0.0127 m thick. What is the rate of heat loss if wall surface temperature is - 12.2 o C inside and 21.1 o C outside? Also what is the temperature at the interface between the outer wall and the corkboard? Values of kwood = 0.1073 W/mo C and kcorkboard = 0.0415 W/mo C

A cold storage room has a walls constructed of 0.102-m corkboard contained between double wooden walls each 0.0127 m thick. What is the rate of heat loss if wall surface temperature is - 12.2 o C inside and 21.1 o C outside? Also what is the temperature at the interface between the outer wall and the corkboard? Values of kwood = 0.1073 W/mo C and kcorkboard = 0.0415 W/mo C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.1P: 1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed...

See similar textbooks

Similar questions

One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
yo lo:ll O %AV L. مرتضی نشط الآن Q5: The piston cylinder device (radius=10 cm) contains a liquid with a pressure 100 kpa and temperature of 20 ° C and has a liquid convection heat coefficient =93 WmK. Connect its fixed side to a cubic piece of aluminum (side length 15 cm) with a thermal conductivity coefficient of aluminum = 239 W mK. At the bottom of the aluminum piece there is a heat source with a temperature of 150 ° C, noting that the heat source is located in a vacuum chamber. Radiation thermal resistance = 3.17 K/W. Calculate the change in piston height during I sec. if you know that there is no change in the internal energy of the piston cylinder device. Note IK Watt 1KJ/s : Aa
(Q3) sk) - A 5mx7m wall consists of 3 glass windows of 1.5mx1.5m dimensions. The wall has thickness of 0.125 m and a thermal conductivity of 0.5 W/m.K. while the glass windows are 6 mm thick with a thermal conductivity of 1:24 W/mK. The values of internal and external surface conductance for the wall (including glass) are 8.1W/m2 K and 34.2 W/m² K, respectively. The internal and external temperatures are 20°C and -30°C, respectively. Calculate the total heat transfer rate through the wall. What percentage of this heat transfer is through the windows? R
QUESTION 2 hot steam pipe (k =16 W/m K) has an inside and outside diameter of 80 mm and 190 mm. If the temperature of the steam is 523 K with h 3000 W/m² K and the outside temperature of the pipe is 353 K. If the pipe is 2 m long compelete the following the thermal resistance of heat transfer by convection is = the conductive heat resistance is the heat transfer per unit length is