A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - Blank 1 mm Inside diameter - Blank 2 mm Lenght - Blank 3 mm Note: All answer must be round off up to 3 decimal places.

Q: If water is cooled from 50OC to -5OC, what is the temperature change on the Celsius, Fahrenheit and…

A:

Q: a) If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: a) Given: Inner diameter=36mm or 0.036mAxial load (F)=5.2×105NMaximum allowable stress…

Q: Given: V = 60 fps, u = 25 fps, ß = 120°. Determine V, in fps. Select one: O a. 31.3 O b. 29.3 O c.…

A: Given data: absolute velocityV=60 fpsvelocity of the bladeu=25 fpsangleβ=120°   Find out: The…

Q: What is the magnitude of the force on an inclined gate shown? The tank contains water and is…

A:

Q: Prob. From the given Fiqure. 150 KN 90° 180 KN 2m A im Reg'd u) vertical reaction at the hinge (2)…

A:

Q: Fill in the blanks: Complete the equation: 10 psiv = in Hg abs **Express final answer in TWO DECIMAL…

A:

Q: A total of 10,000 BTU have been rejected from the condenser in two minutes. If the cooling capacity…

A: Given data Q=10000 BTU=1.055×107 JV=0.45 m3/minT2=120°F=322 K Here, Q is the heat transfer and V is…

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: Refer to the diagram and consider that the pressure in each chamber is equal. Determine the…

A: The force acting on both of the piston faces must be calculated first and then the resultant force…

Q: The throat diameter of a perfect venturi meter is 1.93 inches and is placed horizontally in a pipe…

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A:

Q: 1-14. The density (mass/volume) of aluminum is 5.26 slug/ft. Determine its density in SI units. Use…

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A:

Q: The below figure shows a differential manometer with pipes A and B. The gauge pressure at A is 3…

A:

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm²…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: At what depth below the surface of the oil, relative density 0.89 will produce a pressure of 120…

A: The given data are: Here, d denotes the relative density and P denotes the pressure.

Q: There are 26 heavy smokers in a lounge. The minimum fresh air requirement for smoking lounges by…

A: The minimum diameter of the duct is 0.355 m.

Q: A cylinder contains a fluid at a gauge pressure of 350 kN m-2. Express this pressure in terms of a…

A:

Q: Solve for the stress of a plate (in Pascals) in order to punch a hole 20mm diameter that is 25mm…

A: Given data: d=20 mmt=25 mmF=550 kN Need to determine the stress (shear stress) in the plate.

Q: Find the fluid force on the vertical side of the tank, where the dimensions are given in feet.…

A: Given data Weight density = 62.4 lb/ft^3 Find the force on vertical side of tank.

Q: For pipe shown below Determine the relationship between pressure readings at the numbered points

A:

Q: in figure, the length of wire

A: GIVEN:

Q: A spherical tank for storing gas under a pressure is 20 m in diameter and is made of steel 20 mm…

A:

Q: A tank in the shape of sphere is filled with fluid and then pressurized. The diameter of the tank is…

A: Given data: Diameter of tank =D =3.75 ft = 45 inThickness =t = 0.3750 inLimiting stress =σ = 3750…

Q: Complete the equation: 3 MPaa = kPag **Express final answer in TWO DECIMAL PLACES. Do not round off…

A:

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: For the truss in figure below, the cross-sectional area of the truss members isA = 500 mm²…

Q: Thermal efficiency of a power cycle is 0.8. For the cycle, Qout = 250 kJ. Determine Qin in kJ.

A: Answer: Oin = 1250 kJ.

Q: 28 cm a? 100 cm 15 cm

A:

Q: 3. An automobile tire is inflated to 30 psig pressure at 50 deg. Fahrenheit, after being driven the…

A: To find: The final gauge pressure in psig. Given: The initial pressure is P1=30 psig. The initial…

Q: Prob. From the given Figure. 150 KN 90° 180 KN 2m A Im Reg'd (1) Vertical reaction at the hinge (2)…

A:

Q: 3-The Fluid friction apparatus in (major losses turbulent flows experiment) it is: h/u hoc u Log Ihl…

A: 3) False

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.